CW-SYS WIRELESS DRIVEWAY SYSTEM INSTRUCTIONS
1. WHAT’S IN THE BOX
and on product box. When calling to talk about your product, please have one
of these numbers handy.
PRODUCT
CODE
YEAR
MADE
SERIAL
NUMBER
2. SERIAL NUMBER
1. SENSOR “PUCK”
2. INTEGRATOR
3. AUGER SCREWS (2)
4. CR123A BATTERIES WITH
BATTERY CLIPS (2)
5. 3’ (1 m.) COAXIAL CABLE
6. TERMINAL BLOCK
SCREWDRIVER
3. INSTALLING BATTERIES/LOW BATTERY
1. Use
CR123A
4. PAIRING
YOUR SYSTEM HAS BEEN PAIRED AT FACTORY.
THESE DIRECTIONS APPLYWHEN PAIRING
ADDITIONAL UNITS
6. TESTING RANGE
Your system has a radio range of at least 350 feet or over 1000’ line-of- sight.
Radio range depends on several variables:
How the puck is installed (in ground or above ground on post)
Obstacles blocking radio signal, such as soil, trees, foilage,
buildings, concrete, etc.
To test range:
3. Put sensor in test range mode (see #5 above).
4. Listen for Integrator to trigger. If it doesn’t, move sensor closer to Integrator.
5. Be sure to test again with puck installed in ground (see #8 below).
6. You may need to add a repeater inside the home (see #9 below).
5. TEST MODE FOR SENSOR PUCK
radio signal range (see #6 below).
2. The red LED will blink every second when in test mode
3. There will be an immediate transmission
8. INSTALLING SENSOR PUCK
WARNING: SCREW HOLES IN PUCK WILL STRIP. DO NOT OVERTIGHTEN WITH
SCREW GUN OR TAKE IN & OUT REPEATEDLY. IF SCREWS ARE STRIPPED,
PURCHASE LONGER STAINLESS STEEL SCREWS, SUITABLE FOR PLASTIC.
The sensor puck can be installed in the driveway, in the ground or on an
immovable object (post, tree, etc.).
ON AN OBJECT
1. When range has been tested (see #6 above), seat lid securely on puck with
screws provided. Be careful not to strip screws with screw gun. There should be
no gap between lid and puck.
2. Find a tree, post, or other object directly beside the driveway.
3. Make sure the object is IMMOVABLE or false alarms will occur.
IN THE GROUND
1. When range has been tested (see #6 above), seat lid securely on puck with
screws provided. Be careful not to strip screws with screw gun. There should be
no gap between lid and puck.
2. Find a spot directly beside driveway.
3. Dig a hole big enough for puck and auger screws, allowing puck’s lid to be
level with surface of dirt.
If you fail to secure puck, lawn mowers, etc. will pull/suck it up.
5. Pack and tamp dirt around puck, ensuring lid is clean of dirt and all debris.
IN THE DRIVEWAY
1. When range has been tested (see #6 above), seat lid securely on puck with
screws provided. Be careful not to strip screws with screw gun. There should be
no gap between lid and puck.
2. Use a 4.5
"
diameter masonry hole saw to bore a hole for puck. Bore at least
2.75” deep so puck lid will be 1/4
"
below driveway surface (so it can’t be pulled
up by snow plows, graters, etc.).
7. SETTING SENSITIVITY
ONLY ADJUST (LOWER) SENSITIVITY IF PUTTING IN MIDDLE OF
DRIVEWAY (see #8 below). IN ALL OTHER CASES USE DEFAULT.
SENSITIVITY ADJUSTMENT
HIGH (Default)
Detects vehicle going
5 MPH 12-14’ away
1 & 2 in OFF position
MEDIUM
Detects vehicle going
5 MPH 6-8’ away
1 ON & 2 OFF position
LOW
Detects vehicle going
5 MPH 2-4’ away
1 & 2 in ON position
1
2
ON
1
2
ON
1
2
ON
NOTE: DIP SWITCH
COLOR MAY VARY
2.
Push pairi
(will stay in pairing mode 30 minutes).
3.
Power down
& power up
sensor by un-
installing and
re-installing
(see #3 above).
4.
when paired and exit pairing mode
You can pair up to 10 pucks with unlimited number of Integrators
1.
Bring sensor close to Integrator and
power up Integrator
(see #10 below).
ON AN OBJECT
IN THE GROUND
IN THE DRIVEWAY
1
2
3
4
5
6
IA
OPTIONAL
• 12VDC power
(Part #CW-PSU)
supply
LOOP
SEALANT
1/4"
Don’t allow
sealant to
touch lid
or bosses
Fill line
Use 4.5” masonry hole saw
Pour
sealant
in hole,
then
install
puck.
Do not
cover
lid or
bosses
with
sealant.
• Put logo parallel to drive
• Put just below surface
• Auger screws secure puck
• Do not cover puck lid
• Pack dirt/grass around
puck
• Keep puck lid clean
min.
6
"
- 8
"
• Use stable
object
• Use 4 deck
screws for
fastening
Bore hole
4.5" x 2.75" deep
WARNING: KEEP LID FREE OF DIRT, GRASS, SNOW, & ALL DEBRIS AT ALL TIMES TO ALLOW RADIO SIGNAL TO TRANSMIT!
Pairing
LOW BATTERY
in sensor, Integrator will “chirp”
and its LED will blink RED.
When
hooked
to
external
system’s zone inputs (see #10
below), program what you desire
NOTE: HIGHEST SENSITIVITY IS WITH
DIP SWITCHES IN THE
OFF
POSITION
VERSION 1
to put in
to put in
test mode
test mode
REPLACE BOTH BATTERIES.
DO NOT USE RECHARGEABLES.
IN FREE EXIT INSTALLATIONS, IF ANIMALSOR PEOPLE STEP ONSENSOR
PUCK INSTALLED IN THE GROUND, IT MAY TRIGGER THE GATE TO
OPEN. CONSIDER INSTALLING ON POST OR IN DRIVEWAY INSTEAD.
W
IN
N
ER
WINNER
