background image

THIS APPLIANCE CAN BE USED BY CHILDREN AGED FROM 3 YEARS AND 

ABOVE AND PERSONS WITH REDUCED PHYSICAL, SENSORY OR MENTAL 

CAPABILITIES, OR LACK OF EXPERIENCE AND KNOWLEDGE IF THEY HAVE 

BEEN GIVEN SUPERVISION OR INSTRUCTION CONCERNING USE OF THE 

APPLIANCE IN A SAFE WAY AND UNDERSTAND THE HAZARDS INVOLVED. 

 

CHILDREN SHALL NOT PLAY WITH THE APPLIANCE. 

 

CLEANING AND USER MAINTENANCE SHALL NOT BE MADE BY CHILDREN 

DO NOT SWITCH THE APPLIANCE ON IF YOU SUSPECT THE APPLIANCE  

OF BEING FROZEN.  WAIT UNTIL YOU ARE SURE IT HAS THAWED OUT. 

 

 

 

Section 1 

Important Safety 

Information 

 

 

Your handwash unit has been designed for 

convenience, economy and safety of use, 

provided that it is installed, used and 

maintained in good working order and in 

accordance with our instructions and 

recommendations. 

 

ALL WIRING AND INSTALLATION 

MUST BE SUPERVISED BY A 

SUITABLY QUALIFIED PERSON. 

 

THIS APPLIANCE MUST BE 

EARTHED. 

 

The installation must be in accordance with 

the current edition of BS.7671 (

the ‘IET Wiring 

Regulations’) and ‘Part P’ of the ‘Building 

Regulations’ in force at the time of installation.                                                                   

Installations outside England and Wales must 

also conform to any local regulations in effect 

 

This appliance is intended to be permanently 

connected to the fixed electrical wiring of the 

mains supply with its own dedicated supply, 

however it can be connected with a 13amp 

socket and plug. 

 

This appliance must 

NOT be fitted where it 

may be subjected to freezing conditions. 

 

Isolate the mains electrical and water supply 

before removing the appliance front cover. 

 

DO NOT fit any sort of tap or control on the 

appliance outlet.       

                                                   

 

 

Take care to avoid restricting the outlet of the 

pressure relief device.                                          

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If water is discharged from the pressure relief 

device, maintenance will be required before the 

appliance can be safely used.

 

 

Section 2 Advice To 

Users 

 

The following points will help you have a greater 

understanding of how your handwash works: 

 

 

The electric heating element operates at a 

constant rate.                                                         

The required water temperature is achieved 

by adjusting the rate of water flow via the 

control knob.  

The higher the water flow the lower the 

temperature and vice versa.                                               

The temperature of the water supplied from 

the mains can vary considerably throughout 

the year from 5 to 20°C.                                            

This means that in the winter, flow rate will be 

less than in the summer to achieve the same 

outlet temperature.                                                                                                                                                                   

 

Your handwash is designed to work within a 

range of water pressures, if the pressure falls 

below the minimum pressure required, it is 

likely that the pressure switch will turn off the 

power to the heating element, resulting in 

cold water being produced by the unit.                

(see page 3 for details)  

 

 

Plan your own installation carefully.                              

Check on the nearest and most readily accessible 

rising mains water supply. 

 

 

Summary of Contents for Redring RAHW3









Reviews: