manualshive.com logo in svg

gledhill GB35C, Design, Installation And Servicing Instructions, Page: 55 / 56

Share
Download
gledhill GB35C Design, Installation And Servicing Instructions Download Page 55

Page 55

c

ONDENSING 

c

OMBI BOILE

r

of three years from the date of delivery Gledhill will replace, free of charge, any plate heat exchanger fitted in 
the appliance as original equipment in which scale formation occurs that materially reduces the effectiveness 
of the plate heat exchanger.  This guarantee does not extend to any other component installed within the 
Gledhill appliance or elsewhere in the Purchasers domestic water system.

9.4.
9.4.1. In respect of goods supplied by us  and in respect of any installation work carried out by or on our behalf, our 

entire liability and the purchaser’s sole remedies (subject to the Guarantees) shall be as follows:-
(a) We accept liability for death or personal injury to the extent that it results from our negligence or that of 

our employees

(b) Subject to the other provisions of this clause 9 we accept liability for direct physical damage to tangible 

property to the extent that such damage is caused by our negligence or that of our employees, agents or 
subcontractors.

(c) Our total liability to the purchaser over and above any liability to replace under the Guarantees (whether 

in contract or in tort including negligence) in respect of any one cause of loss or damage claimed to result 
from any breach of our obligations hereunder, shall be limited to actual money damages which shall not 
exceed £20,000 provided that such monetary limit shall not apply to any liability on the part of ourselves 
referred to in paragraph (a) above

(d) Except as provided in paragraph (a) above but otherwise not withstanding any provision herein contained 

in no event shall we be liable for the following loss or damage howsoever caused and even if foreseeable 
by us or in our contemplation:-

   

(i) economic loss which shall include loss of profits, business revenue, goodwill or anticipated savings 

   

(ii) damages in respect of special indirect or consequential loss or damage (other than death, personal 

injury and damage to tangible property)

   

(iii) any claim made against the purchaser by any other party (save as expressly provided in paragraph (b) 

above)

(e) Except  in  respect  of  our  liability  referred  to  in  paragraph  (a)  above  no  claim  may  be  made  or  action 

brought (whether in contract or in tort including negligence) by the purchaser in respect of any goods 
supplied by us more than one year after the date of the invoice for the relevant goods.

(f) Without  prejudice  to  any  other  term  we  shall  not  be  liable  for  any  water  damage  caused  directly  or 

indirectly as a result of any leak or other defect in the goods.    We cannot control the conditions of use of 
the goods or the time or manner or location in which they will be installed and the purchaser agrees to 
be fully responsible for testing and checking all works which include the goods at all relevant times (up 
to, including and after commissioning) and for taking all necessary steps to identify any leaks and prevent 
any damage being caused thereby.

(g) Nothing in these Conditions shall confer on the purchaser any rights or remedies to which the purchaser 

would not otherwise be legally entitled

10. LOSS OR INJURY 

Notwithstanding any other provision contained herein the purchaser’s hereby agree to fully indemnify us against 
any damages losses costs claims or expenses incurred by us in respect of any claim brought against us by any third 
party for:-
(a)

any loss injury or damage wholly or partly caused by any goods supplied by us or their use.

(b)

any loss injury or damage wholly or partly caused by the defective installation or substandard workmanship 
or materials used in the installation of any goods supplied by us.

(c)

any loss injury or damage in any way connected with the performance of this contract.

(d)

any loss resulting from any failure by the purchaser to comply with its obligations under these terms as to 
install and/or check  works correctly.

PROVIDED

 that this paragraph will not require the purchaser to indemnify us against any liability for our own acts 

of negligence or those of our employees agents or sub-contractors

FURTHER

 in the case of goods supplied by us which are re-sold and installed by a third party by the purchaser it will 

be the sole responsibility of the purchaser to test the goods immediately after their installation to ensure that inter 
alia they are correctly installed and in proper working order free from leaks and are not likely to cause any loss injury 
or damage to any person or property.

11. VARIATION OF WARRANTY AND EXCLUSION

Should our warranty and exclusion be unacceptable we are prepared to negotiate for variation in their terms but 
only on the basis of an increase in the price to allow for any additional liability or risk which may result from the 
variation.
Purchasers are advised to insure against any risk or liability which they may incur and which is not covered by our 
warranty.

12. RISK AND RETENTION OF TITLE

(a)

goods  supplied  by  us  shall  be  at  the  Purchaser’s  risk  immediately  upon  delivery  to  the  Purchaser  or  into 
custody on the Purchaser’s behalf or to the Purchaser’s Order.  The Purchaser shall effect adequate insurance 
of the goods against all risks to the full invoice value of the goods, such insurance to be effective from the time 
of delivery until property in the goods shall pass to the Purchaser as hereinafter provided.

(b)

property in the goods supplied hereunder will pass to the Purchaser when full payment has been made by the 
Purchaser to us for :-
(i) the goods of the subject of this contract.
(ii) all other goods the subject to of any other contract between the Purchaser and us which, at the time of 

payment of the full price of the goods sold under this contract, have been delivered to the Purchaser but 
not paid for in full.

(c)

until property in the goods supplied hereunder passes to the Purchaser in accordance with paragraph (2) 
above.
(i) the Purchaser shall hold the goods in a fiduciary capacity for us and shall store the same separately from 

any other goods in the Purchaser’s possession and in a manner which enables them to be identified as our 
goods.

(ii) the Purchaser shall immediately return the goods to us should our authorised representative so request.  

All the necessary incidents associated with a fiduciary relationship shall apply.

(d)

the Purchaser’s right to possess the goods shall cease forthwith upon the happening of any of the following 
events, namely :-
(i) if the Purchaser fails to make payment in full for the goods within the time stipulated in clause 4 hereof.
(ii) if the Purchaser, not being a company, commits any act of bankruptcy, makes a proposal to his or her 

creditors for a compromise or does anything which would entitle a petition for a Bankruptcy Order to be 
presented.

(iii) if  the  Purchaser,  being  a  company,  does  anything  or  fails  to  do  anything  which  would  entitle  an 

administrator or an administrative receiver or a receiver to take possession of any assets or which would 
entitle any person to present a petition for winding up or to apply for an administration order.

(e)

the Purchaser hereby grants to us an irrevocable licence to enter at any time any vehicle or premises owned 
or  occupied  by  the  Purchaser  or  in  the  possession  of  the  Purchaser  for  the  purposes  of  repossessing  and 

recovering  any  such  goods  the  property  in  which 
has  remained  in  us  under  paragraph  (2)  above.    We 
shall  not  be  responsible  for  and  the  Purchaser    will 
indemnify  us  against  liability  in  respect  of  damage 
caused to any vehicle or premises in such repossession 
and  removal  being  damaged  which  it  was  not 
reasonably practicable to avoid.

(f)

notwithstanding paragraph (3) hereof and subject to 
paragraph (7) hereof, the Purchaser shall be permitted 
to sell the goods to third parties in the normal course 
of  business.    In  this  respect  the  Purchaser  shall  act 
in  the  capacity  of  our  commission  agent  and  the 
proceeds of such sale :-
(i) shall  be  held  in  trust  for  us  in  a  manner  which 

enables  such  proceeds  to  be  identified  as  such, 
and :

(ii) shall not be mixed with other monies nor paid into 

an overdrawn bank account.

We,  as  principal,  shall  remunerate  the  Purchaser  as 
commission  agent  a  commission  depending  upon 
the surplus which the Purchaser can obtain over and 
above  the  sum,  stipulated  in  this  contract  of  supply 
which will satisfy us.

(g)

in  the  event  that  the  Purchaser  shall  sell  any  of  the 
goods  pursuant  to  clause  (6)  hereof,  the  Purchaser 
shall  forthwith  inform  us  in  writing  of  such  sale  and 
of the identity and address of the third party to whom 
the goods have been sold.

(h)

if,  before  property  in  the  goods  passes  to  the 
Purchaser under paragraph (2) above the goods are or 
become affixed to any land or building owned by the 
Purchaser it is hereby agreed and declared that such 
affixation shall not have the effect of passing property 
in the goods to the Purchaser.  Furthermore if, before 
property  in  the  goods  shall  pass  to  the  Purchaser 
under paragraph (2) hereof, the goods are or become 
affixed to any land or building (whether or not owned 
by the Purchaser), the Purchaser  shall:-
(i) ensure that the goods are capable of being removed 

without material injury to such land or building.

(ii) take  all  necessary  steps  to  prevent  title  to  the 

goods from passing to the landlord of such land 
or building.

(iii) forthwith  inform  us  in  writing  of  such  affixation 

and  of  the  address  of  the  land  or  building 
concerned.

The  Purchaser  warrants  to  repair  and  make  good 
any  damage  caused  by  the  affixation  of  the  goods 
to  or  their  removal  from  any  land  or  building  and 
to  indemnify  us  against  all  loss  damage  or  liability 
we  may  incur  or  sustain  as  a  result  of  affixation  or 
removal.
(i) in  the  event  that,  before  property  in  the  goods 

has passed to the Purchaser under paragraph (2) 
hereof, the goods or any of them are lost, stolen, 
damaged or  destroyed :-

(ii) the Purchaser shall forthwith inform us in writing 

of the fact and circumstances of such loss, theft, 
damage or destruction.

(iii) the Purchaser shall assign to us the benefit of any 

insurance  claim  in  respect  of  the  goods  so  lost, 
stolen, damaged or destroyed.

13. NON-PAYMENT

If the Purchaser shall fail to make full payment for the goods 
supplied  hereunder  within  the  time  stipulated  in  clause  4 
hereof or be in default of payment for any other reason then, 
without prejudice to any of our other rights hereunder, we 
shall be entitled to stop all deliveries of goods and materials 
to the Purchaser, including deliveries or further deliveries of 
goods under this contract.  In addition we shall be entitled 
to terminate all outstanding orders.

14. VALUE ADDED TAX

All  prices  quoted  are  exclusive  of  Value  Added  Tax  which 
will be charged at the rate ruling at the date of despatch of 
invoice.

15. TRADE SALES ONLY

We  are  only  prepared  to  deal  with  those  who  are  not 
consumers  within  the  terms  of  the  Unfair  Contract  Terms 
Act  1977,  the  Sale  of  Goods  Act  1979  and  the  Supply  of 
Goods and Services Act 1982.  Accordingly any person who 
purchases from us shall be deemed to have represented that 
he is not a consumer by so purchasing.

16. JURISDICTION

The  agreement  is  subject  to  English  law  for  products 
delivered in England and Scottish law for products delivered 
in  Scotland  and  any  dispute  hereunder  shall  be  settled  in 
accordance therewith dependent upon the location.

Summary of Contents for GB35C

























































Reviews:

No comments