manualshive.com logo in svg

GLD Products RENO 7, Manual

Share
Download
GLD Products RENO 7 Manual Download Page 11

GLD Products

RENO 7’ Pool Table

Item 64-0126

11

1-800-225-7593

www.gldproducts.com

STEP 6

  

- INSTALL SUPPORT BEAMS

1. The table base is now right-side up. To install the two support beams (#10), position the 

support beams on the base assembly in the appropriate slots. 

2. Insert a bolt (#17) with a washer (#18) through the side support. 

3. Insert a barrel nut (#13) into the hole at the end of the beam, making sure the slot is 

visible and the slot lines up with the bolt. Thread the bolt into the barrel nut. If the barrel 
nut drops too far into the hole in the support beam, the threads will not engage. If this 
happens, use a magnet or turn the support beam over to remove the barrel nut.  Thread 
the bolt into the barrel nut.

4.  When the bolt is in place the nut can be pushed down to line up with the bolt. Thread the 

bolt into the barrel nut.

5. Hold the support beam in place by screwing in the side support bolt until snug, not tight.

6. Insert two screws (#22) in the ends of the support beams and tighten with a Phillips 

screwdriver.

7. Tighten the bolts using a 12 mm socket wrench. 

NOTE:

The support beams should not rise up above the surrounding frame. If this happens 

loosen the bolt until the support drops. The bolt can be tightened after the top is on 
and secure.

8. The base can now be leveled.
. 

#1

8

#17

#13

#10

#1

8

#17

#22

Summary of Contents for RENO 7

























Reviews:

No comments

Brands by name

Popular brands

Load more brands