Glacier bay 1005403614, Use And Care Manual

Page: 31 / 36

7
Instalación del conjunto del grifo
8
Fijación del conjunto del grifo
8
Installing the soap dispenser
From under the sink, screw the soap dispenser (T) onto the
soap assembly (O) shank. Insert the soap pump (Q) down
into the soap assembly (O).
Insert the soap assembly (O) through the selected hole
in the sink. Secure the soap assembly(O) to the sink with
Flushing and checking for
Pull the hose assembly out of the spout and
the spray head by unscrewing it from the hose in a
counterclockwise direction. Be sure to hold the end of
the hose down into the sink and turn the faucet to
the warm position where it mixes hot and cold water.
Flush the water lines for one minute. This flushes away
any debris that could cause damage to internal parts.
Check for leaks.
Re-tighten any connections if necessary, but do not
IMPORTANT: After installation is completed, turn on the
hot and cold water supplies. Check for leaks. Do not lose
the gasket (1) in the hose.
Topmount Installation (continued)
6
Instalación del fregadero
Aplicar un cordón de silicona alrededor del perímetro de la parte superior del fregadero.
Situar y alinear el hueco debajo de la encimera del fregadero.
Una vez que el fregadero esté en la posición correcta, instalar las presillas de montaje (no incluidas). Apretar las presillas de montaje hasta que el borde
del fregadero esté alineado con la encimera.
Compruebe la alineación mientras lo mueve, de modo que la parte frontal del fregadero (A) quede paralela a la encimera. Ajustar y volver a apretar
Limpiar el exceso de silicona con un trapo.
Instalación por abajo (continuación)
HOMEDEPOT.COM/GLACIERBAY
Póngase en contacto con 1-855-HDGLACIER para obtener más asistencia.
13
Diagrama de montaje:
Encimera
Inserto
Presilla
Fregadero
Silicona para
sellar
Tornillo
4
Shut off the water supply.
Insert the faucet body (L) through the hole in the
sink.
5
Securing the faucet assembly
From underneath the sink, secure the faucet
assembly to the sink with the FastMount™
system (M). Push the FastMount™ system (M)
up over the threads until it stops against the
bottom of the sink, then hand turn (clockwise)
to tighten (Fig 1).
Installing the faucet assembly
Sink
Sink
Push
up
Screw
Fig 1
L
CAUTION: Always shut off the water supply before
removing an existing faucet or replacing any part of a
faucet. Open the faucet handle to relieve water pressure
and ensure that the water is completely shut off.
7
Installing the weight
Insert the weight (O) onto the clip (P) by sliding
it down onto the clip (P).
Install the weight clip (P) at the point of the
hose marking “weight here”.
6
Attaching the quick connector
to the receiving block
Push the quick connector (N) firmly upward and
attach it to the receiving block (1). Pull down
moderately to ensure the connection has been
made.
Topmount Installation (continued)
PRECAUCIÓN: Cierre siempr
grifo existente o reemplazar cualquier parte de un grifo. Abra el grifo
ra aliviar la presión del agua y asegúr
agua está completamente cerrado.
Desconectar el suministro de agua.
Insertar el cuerpo del grifo (L) a través del orificio en el fregadero.
Por debajo del fregadero, fijar el conjunto del grifo al fregadero
con el sistema FastMount™ (21). Empujar el sistema
FastMount™ (21) hacia arriba sobre las roscas hasta que
(en sentido de las agujas del reloj) para apretarlo.
Installation (continued)
5
Securing the faucet assembly
6
Installing the sink
From underneath the sink, secure the faucet assembly to the
sink with the Fastmount™ system (21). Push the Fastmount™
system (21) up over the threads until it stops against the
bottom of the sink, then hand turn (clockwise) to tighten.
Apply silicone sealant (not included) around the underside and lip of the sink (A).
Carefully lower the sink (A) into the counter.
Rotate the clips. Tighten the screws on the top mount clips (AA) evenly until the
sink (A) is flush with the counter. Do not overtighten.
Wipe excess sealant with a rag.
5
6
Installation (continued)
Securing the faucet assembly
Installing the sink
21
Sink Push
up
21
1 1
Push
up
21
2
3
3
Sink
21
Sink
Continue to push up
and turn clockwise
to tighten
From underneath the sink, secure the faucet assembly to the
sink with the Fastmount
TM
system (21). Push the Fastmount
TM
system (21) up over the threads until it stops against the
bottom of the sink, then hand turn (clockwise) to tighten.
Apply silicone sealant (not included) around the underside and lip of the sink (A).
Carefully lower the sink (A) into the counter.
Rotate the clips. Tighten the screws on the top mount clips (AA) evenly until the
sink (A) is flush with the counter. Do not overtighten.
Wipe excess sealant with a rag.
5
6
Installation (continued)
Securing the faucet assembly
Installing the sink
21
Sink Push
up
21
1 1
Push
up
21
2
3
3
Sink
21
Sink
Continue to push up
and turn clockwise
to tighten
From underneath the sink, secure the faucet assembly to the
sink with the Fastmount
TM
system (21). Push the Fastmount
TM
system (21) up over the threads until it stops against the
bottom of the sink, then hand turn (clockwise) to tighten.
Apply silicone sealant (not included) around the underside and lip of the sink (A).
Carefully lower the sink (A) into the counter.
Rotate the clips. Tighten the screws on the top mount clips (AA) evenly until the
sink (A) is flush with the counter. Do not overtighten.
Wipe excess sealant with a rag.
Push
up
Sink
Push
up
Sink
Sink
Continue to push up
and turn clockwise
to tighten
Empu-
jar
Frega-
dero
Fregadero
Continúe empujando
hacia arriba y gire
en sentido horario
Empu-
jar
Frega-
dero
pa
ese de que el suministro de
Installing the soap dispenser
From under the sink, screw the soap dispenser (T) onto the
soap assembly (O) shank. Insert the soap pump (Q) down
Insert the soap assembly (O) through the selected hole
in the sink. Secure the soap assembly(O) to the sink with
the spray head by unscrewing it from the hose in a
counterclockwise direction. Be sure to hold the end of
the hose down into the sink and turn the faucet to
the warm position where it mixes hot and cold water.
Flush the water lines for one minute. This flushes away
any debris that could cause damage to internal parts.
Re-tighten any connections if necessary, but do not
IMPORTANT: After installation is completed, turn on the
hot and cold water supplies. Check for leaks. Do not lose
opmount Installation (continued)
Installing the soap dispenser
From under the sink, screw the soap dispenser (T) onto the
soap assembly (O) shank. Insert the soap pump (Q) down
Insert the soap assembly (O) through the selected hole
in the sink. Secure the soap assembly(O) to the sink with
the spray head by unscrewing it from the hose in a
counterclockwise direction. Be sure to hold the end of
the hose down into the sink and turn the faucet to
the warm position where it mixes hot and cold water.
Flush the water lines for one minute. This flushes away
any debris that could cause damage to internal parts.
Re-tighten any connections if necessary, but do not
IMPORTANT: After installation is completed, turn on the
hot and cold water supplies. Check for leaks. Do not lose
opmount Installation (continued)
Installing the soap dispenser
From under the sink, screw the soap dispenser (T) onto the
soap assembly (O) shank. Insert the soap pump (Q) down
Insert the soap assembly (O) through the selected hole
in the sink. Secure the soap assembly(O) to the sink with
the spray head by unscrewing it from the hose in a
counterclockwise direction. Be sure to hold the end of
the hose down into the sink and turn the faucet to
the warm position where it mixes hot and cold water.
Flush the water lines for one minute. This flushes away
any debris that could cause damage to internal parts.
Re-tighten any connections if necessary, but do not
IMPORTANT: After installation is completed, turn on the
hot and cold water supplies. Check for leaks. Do not lose
opmount Installation (continued)
From under the sink, screw the soap dispenser (T) onto the
soap assembly (O) shank. Insert the soap pump (Q) down
in the sink. Secure the soap assembly(O) to the sink with
opmount Installation (continued)
From under the sink, screw the soap dispenser (T) onto the
soap assembly (O) shank. Insert the soap pump (Q) down
in the sink. Secure the soap assembly(O) to the sink with
opmount Installation (continued)
Installing the soap dispenser
From under the sink, screw the soap dispenser (T) onto the
soap assembly (O) shank. Insert the soap pump (Q) down
Insert the soap assembly (O) through the selected hole
in the sink. Secure the soap assembly(O) to the sink with
the spray head by unscrewing it from the hose in a
counterclockwise direction. Be sure to hold the end of
the hose down into the sink and turn the faucet to
the warm position where it mixes hot and cold water.
Flush the water lines for one minute. This flushes away
any debris that could cause damage to internal parts.
Re-tighten any connections if necessary, but do not
IMPORTANT: After installation is completed, turn on the
hot and cold water supplies. Check for leaks. Do not lose
opmount Installation (continued)
Installing the soap dispenser
From under the sink, screw the soap dispenser (T) onto the
soap assembly (O) shank. Insert the soap pump (Q) down
Insert the soap assembly (O) through the selected hole
in the sink. Secure the soap assembly(O) to the sink with
the spray head by unscrewing it from the hose in a
counterclockwise direction. Be sure to hold the end of
the hose down into the sink and turn the faucet to
the warm position where it mixes hot and cold water.
Flush the water lines for one minute. This flushes away
any debris that could cause damage to internal parts.
Re-tighten any connections if necessary, but do not
IMPORTANT: After installation is completed, turn on the
hot and cold water supplies. Check for leaks. Do not lose
opmount Installation (continued)