Glacier bay 1001-240-663 Installation And Care Manual Download Page 2

 

2

Table of Contents

Important Information

 

..............................2

Warranty ...................................................2
Pre-Installation .........................................3

Planning Installation ..............................3

P

ackage Contents

 ..................................6

Installation ................................................7
Care and Cleaning ....................................14
Troubleshooting  

........................................15

Service Parts ...........................................16

Important Information

□ 

Do not install this product until you read and understand the instructions in this manual. If you are installing this

    product for someone else, leave this manual for the owner’s/ user’s reference.

□ 

Inlet ports are designed to allow for 1/2 in. COPPER tubing solder connection or 1/2 in. IPS threading coupling

    connection. For threaded connections, wrap sealant tape around threaded ends before connecting. If soldering
    connections, certain inflammable parts should be removed prior to the soldering in order to avoid heat damage.
    If you are unsure how to properly remove these parts, please call us at 1-855-HD-Glacier.

□ 

Protect your eyes with safety glasses when cutting or soldering water supply lines.

□ 

NOISE AND WATER HAMMER IN PEX SYSTEMS: Due to the inherent flexibility of PEX compared with metallic

    plumbing materials, water hammer and noise can sometimes occur from the pressure surges. It is important to
    ensure the tubing is not in contact with wallboard, forced air ducts or other high-resonance materials. Clamping
    or strapping can help prevent these noises. DO NOT USE PEX tubing from the valve to the tub spout.

Tools and Hardware Required

 

...............3

Warranty

LIMITED LIFETIME WARRANTY

Glacier Bay products are manufactured with superior quality standards and workmanship and are backed by our 
limited lifetime warranty. Glacier Bay products are warranted to the original consumer purchaser to be free of 
defects in materials or workmanship. We will replace FREE OF CHARGE any product or parts that proves defective. 
Simply, return the product / part to any of The Home Depot retail locations or call 1-855-HD-GLACIER (1-855-434-
5224) to receive the replacement item. Proof of purchase (original sales receipt) from the original consumer 
purchaser must be made available for all Glacier Bay warranty claims.

This warranty excludes incidental/inconsequential damages and failures due to misuse, abuse or normal wear and 
tear. This warranty excludes all industrial, commercial and business usage, whose purchasers are hereby extended 
a five year limited warranty from the date of purchase, with all other terms of this warranty applying except the 
duration of warranty.

Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, so the 
above limitations may not apply to you. This warranty gives you specific legal rights and you may also have other 
rights that vary from state to state and province to province. Please see a store or contact 1-855-HD-GLACIER for 
more details.
Contact the Customer Service Team at 1-855-434-5224 or visit www.HomeDepot.com.

Summary of Contents for 1001-240-663



































Reviews: