background image

6

4

5

D-TECT Laser 509  

D-TECT Laser 505

-

-

-

-

MIN

MAX

MIN

MAX

6

CAT 2

CAT 2

3 s

max. 30 s

Wait for the sensor to learn its environment 
or lock it by remote control.

left

right

left

right

WITH BACKGROUND

WITHOUT BACKGROUND

centre

MOUNTING SIDE

SAFETY FIELD DIMENSIONS

Launch a teach-in after changing the sensor position or when new objects are added to or changed in the detection 

zone. 

WIDTH

HEIGHT

IMPORTANT

Test the good functioning of the installation before leaving the premises.

0.5 m

9.9 m

0.5 m

5.0 m

5.0 m

0.5 m

9.9 m

0.5 m

5.0 m

5.0 m

no field

no field

The detection field should be free of snow buildups, heavy rain, snowfall, fog or other moving objects.

Stay outside of the detection field to avoid disturbances.

Select the corresponding mounting side.

The sensor learns its environment and automatically determines the detection field(s). 

Both RED LEDs flash slowly and the 3 visible laser beams automatically light up during 30 seconds.

EXAMPLE

for a field width of 6.2 m

The sensor memorizes the 
floor as reference point 
and signals a fault when its 
orientation is changed.

No reference point, no signal.

During teach-in, the sensor learns its surroundings and adapts the detection field 

shape to these. Objects in the detection field will be cut out.

TEACH-IN

Summary of Contents for D-TECT GJD505













Reviews: