GITER G2500-24 Installation Manual Download Page 2

Copyright Statement

CONTENT

This manual is under the copyright of GITER Co., Ltd, with all rights reserved. Please keep the 
manual properly and operate in strict accordance with all safety and operating instructions in this 
manual. Please do not operate the system before reading through the manual.

Version Information 

Version

Date

Content

V1.0

20201110

New

1. Introduction

1.1 General precaution

2. Installation

2.1 Scope of delivery

2.2 GTE battery

2.3 Limitation of liability

2.4 Installation of the battery

       2.4.1 Installation site and environment

       2.4.2 Unpacking the box

       2.4.3 Installation and wiring

3. System operation

3.1 Power on/off

4. Maintenance and fault handling

4.1 Routine maintenance

4.2 Handling of other faults and abnormal phenomena

 

4.2.1 Unable to turn on 

       4.2.2 Shut down immediately after turn on 

       4.2.3 Unable to charge 

       4.2.4 Unable to discharge 

       4.2.5 No communication between battery and upper controller (if any)

  4.2.6 Unable to turn off

       4.2.7 Outer light is always on

5. Appendix

5.1 Specification

01
01
02
02
02
06
06
06
06
07
11
11
11
11
11
11
11
12
12
12
13
13
13
13

Summary of Contents for G2500-24










Reviews: