Count
inherits advantages of previous versions of our LED
Ringlight while adding some new and exciting fea-
tures. By expanding the brightness of LEDs, this unit
uses high RA up to 100 LEDs to provide users with
the highest quality color rendition. By implementing the
latest LED technology, users can enjoy various flexible
combinations and innovative methods of LED lighting
that make the subject’s color and appearance more
vibrant.
Keep dry
Do not handle with wet hands, immerse or expose
to water or rain, or handle without care. Failure to
observe this precaution could result in electric shock
or fire.
Do not use in the presence of flammable gas
Failure to do so could result in an explosion or fire.
Keep out of reach of children
This device contains small parts which may pose
a choking hazard. Consult a physician immediately
if a child swallows any part/s of this device.
Do not expose to high temperatures
Do not leave this device in a closed vehicle under
the sun or in other areas subject to high temper-
atures. Failure to observe this precaution could
result in a fire or damage to the casing or internal
parts.
Observe precaution when handling batteries.
Use only batteries listed in this manual. Do not mix
old and new batteries or batteries or different types.
Do not short or disassemble.
Do not attemprt to insert batteries upside down or
backwards.
Batteries may leak if fully discharged.
To avoid damage to the product, be sure to remove
the batteries when leaving the product unattended
for prolonged periods of time or when no charge
remains in the batteries.
Should liquid from the batteries come into contact
with skin or clothing, IMMEDIATELY rinse it off with
fresh water and contact a physician immediately.
1. Test The flash output
2. Switch to flash mode
Press L/R button to switch between
left, right, and full brightness mode
Switch to light mode
1. Insert four AA batteries into the battery storehouse.
2. Attach the hotshoe head of Ringlight Controller to
the camera’s hotshoe, then release.
3. Ringlight Setup:
-Use the appropriate ring mount according to size
of the lens.
-Place the ring mount on the lens.
-Hold and place the Ringflash on the ring mount.
-Lock it into place to finish installation.
The Ringlight has 3 stops under Flash and Light mode.
“Flash” mode light output is twice the amount as “Light”
mode light output.
1. QTR represents a quarter of maximum brightness
2. HALF represents half of the maximum brightness
3. FULL represents the full maximum brightness
1.
Underexposed or overexposed photos
Be sure the camera’s shutter, aperature or ISO
setting is not too high or low. Check exposure
compensation, exposure bracketing, and flash
related settings as well.
2.
Vignetting
Do not use wide angles, and adjust the camera’s
focal length to 50 mm or more.
3.
Flash does not work
Be sure the battery has power. If not replace it with
a charged one, or recharge it as soon as possible.
During the battery installation, follow the +/- icons.
Be sure the camera and flash hotshoe is clean. If
not, clean it carefully with a cloth, and then re-
install using our provided installation instructions on
page 4.
4.
Abnormal flash
Turn off Ringflash and camera. Carefully remove
the ringflash from the camera. Reinstall the
ringflash using our provided installation instructions
on page 4. If problems continue to persist, replace
the batteries and try again.
To prevent damage to your product or injury to
yourself and others, please carefully read the
following safety precautions in their entirety before
using any of this equipment. Keep these safety
instructions where all those who use this equipment
will read them.
Do not disassemble or modify
Failure to observe this precaution could result in
electric shock or product malfunction. Should this
product break open as a result of a fall or other
accident, please remove the batteries carefully.
10. Double the brightness compared to other brands
Flashmate II N101C (Canon)
Flashmate II N101N (Nikon)
The GiSTEQ Flashmate II LED Lighting System
TM
True And
Natural
Color
