background image

GSR 36/48V 

Technical manual

  

   

Model 36/48

       Electrical connection and plugging

1 ) Set the DIP switch 1 according to the voltage of the battery in use 36 V or 48 V.
If the GSR 36/48 is powered by an incorrect  configuration of the dip switch can ruin the  
battery or not function properly.

          2 ) Set the DIP switch 2 according to the type of battery (Pb or LiFePo ) as described in the 

following table 1 ( configuration dip-switch) . If the GSR 36/48 is powered by an incorrect 
configuration of the dip -switch can ruin the battery or not function properly.

3 ) Set the DIP switch 3 according to the type of LOAD expected, 24 h or at night.

4) Install the GSR 36/48 in a dry place , not exposed to rain and adequately ventilated. 
During its operation the GSR 36/48 generate more heat and keep warm , to prevent entry 
into operation its overtemperature protection you need to keep a clear space around it so 
that it can circulate air that helps cooling.

5) Make the electrical connections as shown in Fig. 2,
First of all connect the Load, then the battery and last the PV module. If this sequence is   
respected the GSR may signal a battery error( red led stable).

 

be sure to use the electric cables to the appropriate section of current that must flow . As 
soon as the battery is connected both LEDs light up for a second to report good start to 
the charge controller.

6 ) Test the installation just connected by verifying that the system charges the battery. 
With  the  PV  module  exposed  to  good   light  ,  verify   that  the  green   LED   is  flashing,   it  
indicates that charging current is flowing into the battery. For a closer examination of the 
proper   functioning   of   the   regulator   is   recommended   to   check   with   a   voltmeter   while  
charging the battery voltage measured at the terminals of the PV module PV + and GND is 
close   to   the   maximum   output   voltage   of   the   photovoltaic   module   in   use   (   see   the  
datasheet module to locate the voltage of maximum power typically referred to as Vmp . 
During this test, make sure the battery has a voltage lower than the voltage - end load 
set.

This document is the property of  

Giocosolutions S.r.l. 

3

Summary of Contents for GSR 36/48V








Reviews: