5
5
FEATURES
The ENT forehead mirrors are local lighting devices with luminous forehead mirror particularly useful to examine
the oral cavity, the nose and the ear.
These products are equipped with mirrors made of special enameled glass and are assembled on a practical helmet,
adjustable and adaptable to the operator’s head.
The following models are available:
CLAR mirror (cod.31132) Ø 100 mm
STORZ mirror (cod. 31135) Ø 55 mm
ADJUSTABLE STORZ mirror (cod. 31138) Ø 55 mm
The packaging includes a 6V bulb (cod. 31145) and a line cord.
To power the mirrors, GIMA delivers the power supply GIMA
6
(cod. 31130). It delivers an output voltage
adjustable from 1,2V to 10 V CC 500 mA.
PRESCRIPTIONS
- The mirrors are very delicate and shall be handled carefully.
The product shall be used by qualified personnel only.
Do not use the equipment in case it is damaged. Apply to your retailer.
Avoid precarious repairs. Repairs shall be carried out with original spare parts only, which shall be
installed according to the intended use.
Broken bulbs or mirrors can cause injuries or cut. Carefully handle and immediately replace.
Since the product is made of corrosion-proof materials suitable for the enviromental conditions foreseen for its
normal use, does not require special care, however it is necessary to store it in a closed place making sure that is
protected from dust and dirt to assure its hygenic conditions. Moreover, it is recommended to store the product in
a place which can be reached easily by the personnel in case of necessity.
UNPACKING
Always remember that packing elements (paper, cellophane, stitches, adhesive tape, etc.) can cut and/
or hurt if they are not carefully handled.
They shall be removed with adequate means and shall not be left at the mercy of irresponsible persons;
the same is valid for tools used to remove packages (scissors, knives, etc.).
After opening the packages, first of all it is necessary to check all pieces and parts composing the product. Check
that they are all present and in perfect conditions.
INSTALLATION
- Before using the product, it is possible to adjust the helmet to the head size. To do this, make use of the apposite
adjusting screw located on the side allowing tightening or loosening the headbands.
- The assembly of mirrors is very simple: for models 31132 and 31135 it is enough to insert the supporting pin,
located on the back of the mirror, into the hole of the screw mechanism fixed on the headband front side.
Once the best position has been found, tighten the small knob D.
- For the model 31138, it will be sufficient to insert the ball located at the mirror support end into the apposite seat
on the headband front side and tighten the knob C.
FEATURES
The ENT forehead mirrors are local lighting devices with luminous forehead mirror particularly useful to examine
the oral cavity, the nose and the ear.
These products are equipped with mirrors made of special enameled glass and are assembled on a practical helmet,
adjustable and adaptable to the operator’s head.
The following models are available:
CLAR mirror (cod.31132) Ø 100 mm
STORZ mirror (cod. 31135) Ø 55 mm
ADJUSTABLE STORZ mirror (cod. 31138) Ø 55 mm
The packaging includes a 6V bulb (cod. 31145) and a line cord.
To power the mirrors, GIMA delivers the power supply GIMA 5 (cod. 31130). It delivers an output voltage
adjustable from 1,2V to 10 V CC 500 mA.
PRESCRIPTIONS
- The mirrors are very delicate and shall be handled carefully.
The product shall be used by qualified personnel only.
Do not use the equipment in case it is damaged. Apply to your retailer.
Avoid precarious repairs. Repairs shall be carried out with original spare parts only, which shall be
installed according to the intended use.
Broken bulbs or mirrors can cause injuries or cut. Carefully handle and immediately replace.
Since the product is made of corrosion-proof materials suitable for the enviromental conditions foreseen for its
normal use, does not require special care, however it is necessary to store it in a closed place making sure that is
protected from dust and dirt to assure its hygenic conditions. Moreover, it is recommended to store the product in
a place which can be reached easily by the personnel in case of necessity.
UNPACKING
Always remember that packing elements (paper, cellophane, stitches, adhesive tape, etc.) can cut and/
or hurt if they are not carefully handled.
They shall be removed with adequate means and shall not be left at the mercy of irresponsible persons;
the same is valid for tools used to remove packages (scissors, knives, etc.).
After opening the packages, first of all it is necessary to check all pieces and parts composing the product. Check
that they are all present and in perfect conditions.
INSTALLATION
- Before using the product, it is possible to adjust the helmet to the head size. To do this, make use of the apposite
adjusting screw located on the side allowing tightening or loosening the headbands.
- The assembly of mirrors is very simple: for models 31132 and 31135 it is enough to insert the supporting pin,
located on the back of the mirror, into the hole of the screw mechanism fixed on the headband front side.
Once the best position has been found, tighten the small knob D.
- For the model 31138, it will be sufficient to insert the ball located at the mirror support end into the apposite seat
on the headband front side and tighten the knob C.
