Gigaset SX763 First Steps Download Page 48

Page: 48 / 196

Basic Setup Wizard

Gigaset SX763 WLAN dsl / eng / A31008-M707-R131-8x-7619 / configure_router.fm / 23.10.2008

e 20

05_

_27

PPPoE pass-through

This option is only available if you have chosen another

Protocol

than PPPoE. PPPoE

pass-through allows you to use an additional Internet connection (through another
service provider) on one PC. Further information about this can be found on page 68.

Deactivate

PPPoE pass-through

if you do not wish to use this function.

After entering the data click

Next >

Using UPnP (Universal Plug and Play)

PCs with

UPnP

(Universal Plug & Play) can offer their own network services and automat-

ically use services offered in the network. Further information about this can be found
on page 68.

To go to the next step, click

Next >

Summary of Contents for SX763





































































































































































































Search results

Summary of Contents for SX763

Reviews:

Related manuals for SX763

Brands by name

Popular brands

Gigaset SX763, First Steps

Search results

Summary of Contents for SX763

Reviews:

Related manuals for SX763

Brands by name

Popular brands