Gigaset S328 Operating Instructions Manual Download Page 27

Page: 27 / 65

SMS (text messages)

Gigaset S440 / SWZ-engl nur fuer Internet Swisscom / xxxxxx / sms_BRD_neutral.fm / 21.07.2006

Sending an SMS to an email address

If your service provider supports the 'SMS

to email' service, then you can also send

your text messages to email addresses.

Depends on the provider. This is not

currently supported in the Swisscom

network.
The email address must be written at the

beginning of the text. You must send the

SMS to the email service of your SMS send

centre.

(Mailbox, mailbox PIN)

Write Message

Copy the email address from

the email directory or enter

directly. End with a space or

colon (depending on the serv-

ice provider).

Enter the SMS text.

Press the display key.

Send

Select and press

§OK§

E-mail

Select and press

§OK§

. If the

number of the email service is

not entered (page 28), enter

the number of the email serv-

ice.

Press the display key.

Send

Select and press

§OK§

Receiving an SMS

All SMS received are saved in the incoming

message list. Linked text messages are dis-

played as

one

SMS. If this is too long or

has not been transferred completely, it

will be split into individual messages.

Since an SMS remains in the list after you

have read it, you should

delete SMS reg-

ularly from the list

The display tells you if the message mem-

ory is full.

Deleting SMS you no longer require

(page 25).

Incoming message list

The incoming message list contains:

all SMS received, starting with the most

recent.

messages that could not be sent

despite several attempts.

New SMS are signalled on all Top S328

handsets by the

icon on the display, the

flashing message key

and an advi-

sory tone.

Opening the incoming message list with

the

key

Requirement:

There is a

new

SMS in the

list.

Press.

Select mailbox if necessary and enter mail-

box PIN.
The incoming message list is displayed as

follows (example):

1 Number of new + number of old, read en-

tries

2 Name of mailbox, here: general mailbox

An entry in the list is displayed e.g. as fol-

lows:

01/02: Total number of new SMS/number of the

SMS displayed

Opening the incoming message list via the

SMS menu

(Mailbox, mailbox PIN)

Incoming 01+05

Reading or deleting individual SMS

Open the incoming message list

Continue as described at "Reading or

deleting individual SMS", page 24.

A new message which you have read

acquires the status

Old

SMS: 01+05

1
2

New

01/ 02

1234567890

28.09.04

09:45

Summary of Contents for S328


































































Search results

Summary of Contents for S328

Reviews:

Brands by name

Popular brands

Gigaset S328, Operating Instructions Manual

Search results

Summary of Contents for S328

Reviews:

Brands by name

Popular brands