background image

14

Contact with liquid

If the handset should come into contact with liquid, 

on no account switch 

the device on. Remove all batteries immediately.

Allow the liquid to drain out of the device, and then pat all parts of the device 

dry. Keep the handset with the batteries removed in a warm, dry place for at 

least 72 hours. You will normally then be able to use it again.

Range

The range is up to 300 m in the open. In buildings, ranges of up to 50 m can be 

achieved. If you go outside the range, "*--*--* " appears in the display.

Recommended batteries

Sanyo Twicell 650; Sanyo Twicell 700; Panasonic 700mAh ’for DECT’; 

GP 550mAh; GP 700mAh; YDT AAA 600; YDT AAA Phone 700; 

VARTA PhonePower AAA 700MAh.

Questions and Answers

Service (Customer Care)

You can get assistance easily when you have technical questions or questions about how 

to use your device by using our online support service on the Internet at:

www.my-siemens.com/customercare

or by referring to the section entitled 

Questions and answers

 in this manual.

Question

Possible Cause

Possible solution

Nothing appears in the 

display.

The batteries are flat.

Charge or replace the batteries 

(see page 5). 

No radio link to base – 

display shows

"*--*--*".

Handset outside the 

base station range.

Handset not registered.

Base not switched on.

Reduce distance between handset 

and base.

Register handset

(see page 10).

Check the mains connector on the 

base (see page 4).

The caller’s telephone 

number is not displayed 

although CLIP is set 

(see page 7).

Telephone number 

identification is 

blocked.

The caller must request 

identification of his telephone 

number from his network 

provider.

!

Ontario.fm  Seite 14  Freitag, 28. November 2003  2:35 14

Summary of Contents for Gigaset A110



















Reviews: