manualshive.com logo in svg

GIGAMEDIA GGM GS26L2, User Manual

Share
Download
GIGAMEDIA GGM GS26L2 User Manual Download Page 12

GIGAMEDIA                                                                             

User’s  Guide

_V2.0.7

 

Page 12 of 35 

Part Two WEB Configuration Guide 

Chapter 1    User Login   

GGM  GS26L2  smart  switch  adopt  Web-based  interface  management,  the  default  IP  is 

192.168.255.1. Please make sure the IP address of PC is in the same network segment with 

that of switch, 

or the PC can’t access to manage the switch. After the setting of IP address, 

please input 192.168.255.1 in the browser to access the configuration interface of switch. 

The Web management interface consists of five parts, which are switch status, basic 

configuration, advanced configuration, network security, system maintenance. 

 

Login Page 

Enter user password in the above login page, the default password is admin. The system only 

support single user login, other logins will be refused until the user logs out.   

If IP address conflict occurs, it suggests the latest 

user didn’t log out successfully. Please 

reboot the device or try to log in again180s later. 

It is advised to reset the IP address and password in first login, and make sure the switch is 

not configured in the same network segment with DHCP server or Internet Gateway device.

 

Summary of Contents for GGM GS26L2




































Reviews:

No comments

Brands by name

Popular brands

Load more brands