manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

361 

 

 

In  the regular  group, a sequence of  up  to 9  conversions can be organized in a  specific 
sequence. The  ADC_RSQ0~ADC_RSQ2 registers specify the  selected channels of  the 
regular  group.  The  RL[3:0] bits in  the ADC_RSQ0 register specify the  total conversion 
sequence length. 

In  the inserted group, a sequence of up  to 4  conversions can be organiz ed in a specific 
sequence. The ADC_ISQ register specifies the selected channels of the inserted group. The 
IL[1:0] bits in the ADC_ISQ register specify thetotal conversion sequence length. 

14.4.4. 

Conversion modes 

Single conversion mode 

This mode can be used in both regular and inserted channel groups. In the single conversion 

mode,  the  ADC  performs  conversion  on  the  channel  specified  in  the  RSQ0[4:0] bits  in 

ADC_RSQ2 or the channel specified in the ISQ3[4:0] bits in ADC_ISQ. When the ADCON is 

1, the ADC samples and converts a single channel, once the corresponding software trigger 

or external trigger is active. 

Figure 14-2. Single conversion mode 

CH2

CH2

CH2

CH2

CH2

EOC

Regular

trigger

Sample

Convert

 

After  conversion  of  a  single  regular  channel,  the  conversion  data  will  be  stored  in  the 

ADC_RDATA register, the EOC will be set. An interrupt will be generated if the EOCIE bit is 

set. 

After  conversion  of  a  single  injected channel,  the  conversion  data  will  be  stored  in  the 

ADC_IDATA0 register, the EOC and EOIC will be set. An interrupt will be  generated if  the 

EOCIE or EOICIE bit is set. 

Software procedure for a single conversion of a regular channel: 

1.  Make sure the DISRC, SM in the ADC_CTL0 register and CTN bit in the ADC_CTL1 

register are reset; 

2.  Configure the RSQ0 with the analog channel number; 

3.  Configure the ADC_SAMPTx register; 

4.  Configure the ETMRC and ETSRC bits in the ADC_CTL1 register if it is needed;  

5.  Set the SWRCST bit, or generate an external trigger for the regular group;  

6.  Wait for the EOC flag to be set; 

7.  Read the converted result from the ADC_RDATA register; 

8.  Clear the EOC flag by writing 0. 

Software procedure for a single conversion of an inserted channel:  

1.  Make sure the DISIC, SM in the ADC_CTL0 register are reset; 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

D-Link xStack Storage DSN-4000 Series Datasheet preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 5
Data Translation DT330 Series Getting Started Manual preview
DT330 Series
Brand: Data Translation Pages: 60
e-Line Technology Network Video Recorders User Manual preview
Network Video Recorders
Brand: e-Line Technology Pages: 34
FabiaTech FX5638 Series Users Quick Reference preview
FX5638 Series
Brand: FabiaTech Pages: 4
Keithley 7707 User Manual preview
7707
Brand: Keithley Pages: 59
D-Link AirPlus XtremeG Ethernet-to-Wireless Bridge... Manual preview
AirPlus XtremeG Ethernet-to-Wireless Bridge...
Brand: D-Link Pages: 31
SMART MOD IIC Installation And Service Manual preview
MOD IIC
Brand: SMART Pages: 15
Delta M125HV-113 Quick Installation Manual preview
M125HV-113
Brand: Delta Pages: 2
IEI Technology PUZZLE-IN003B User Manual preview
PUZZLE-IN003B
Brand: IEI Technology Pages: 86
Dahua Technology Lite N42B1P Series Quick Start Manual preview
Lite N42B1P Series
Brand: Dahua Technology Pages: 14
WAGO 750-459 Manual preview
750-459
Brand: WAGO Pages: 48
NKE BOX Wi-Fi User Manual And Installation Manual preview
BOX Wi-Fi
Brand: NKE Pages: 15
MEDIATEK MT6252 Design Manual preview
MT6252
Brand: MEDIATEK Pages: 166
SriHome NVS001B Quick Operation Manual preview
NVS001B
Brand: SriHome Pages: 12
ZALMAN CNPS20X User Manual preview
CNPS20X
Brand: ZALMAN Pages: 20
Lantronix N-FXE 02B Series User Manual preview
N-FXE 02B Series
Brand: Lantronix Pages: 10
ZALMAN CNPS10X Flex User Manual preview
CNPS10X Flex
Brand: ZALMAN Pages: 12
Quantum MC300 Prism User Manual preview
MC300 Prism
Brand: Quantum Pages: 140

Brands by name

Popular brands

Load more brands