manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

150 

 

 

16 

RFSEC 

RF  security 

When  set, the  bits  of PMU_RFCTL  register  is  secure. A non-secure read  /  w rite 

access on secured bits is RAZ / WI. 

15:12 

Reserved 

Must  be kept  at reset value. 

11 

LPSSEC 

Wi-Fi_sleep  and SRAM_sleep  mode  security 

When  set,  the  bits  of PMU_CTL1  register  is  secure.  A  non-secure  read  /  w rite 

access on secured bits is RAZ / WI. 

10 

DBPSEC 

Backup  Domain  w rite access security 

When set, BKPWEN  bit in PMU_CTL0  register is secure. A non-secure read / w rite 

access on secured bits is RAZ / WI. 

9 

VDMSEC 

Voltage detection  and monitoring  security 

When  set, LVDEN,  LVDT[2:0],  VLVDEN  bits  in PMU_CTL0  register are secure.

 

A 

non-secure read / w rite access on secured bits is RAZ / WI. 

8 

LPMSEC 

Low -pow er mode security 

When  set, LDOLP,  STBMOD,  WURST,  STBRST  bits  in  PMU_CTL0  register  are 

secure. A non-secure read / w rite access on secured bits is RAZ / WI. 

7:4 

Reserved 

Must  be kept  at reset value. 

3 

WUP3SEC 

WKUP  pin 3 security 

When  set, WUPEN3  bit  in PMU_CS0  register is secure. A non-secure read / w rite 

access on secured bits is RAZ / WI. 

2 

WUP2SEC 

WKUP  pin 2 security 

When  set, WUPEN2  bit  in PMU_CS0  register is secure. A non-secure read / w rite 

access on secured bits is RAZ / WI. 

1 

WUP1SEC 

WKUP  pin 1 security   

When  set, WUPEN1  bit  in  PMU_CS0  register is secure. A non-secure read / w rite 

access on secured bits is RAZ / WI. 

0 

WUP0SEC 

WKUP  pin 0 security   

When  set, WUPEN0  bit  in PMU_CS0  register is secure. A non-secure read / w rite 

access on secured bits is RAZ / WI. 

5.4.7. 

Privilege configuration  register (PMU_PRICFG) 

Address offset: 0x34 

Reset value: 0x0000 0000 (not reset by wakeup from Standby mode) 

This register can be read by both privileged and unprivileged access. When TZEN = 1, and 

at least one bit in PMU_SECCFG register is set, this register can be read by both secure and 

non-secure access, and only secure write access is allowed. 

This register can be accessed by half-word (16-bit) or word (32-bit). 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

Parker H Series Installation & Service Instructions Manual preview
H Series
Brand: Parker Pages: 344
Magnat Audio MC 200 Faq preview
MC 200
Brand: Magnat Audio Pages: 2
Radwin Transportation FiberinMotion Deployment Manual preview
Transportation FiberinMotion
Brand: Radwin Pages: 122
XESS XStend XS40 User Manual preview
XStend XS40
Brand: XESS Pages: 23
Idis DR-8432 Installation Manual preview
DR-8432
Brand: Idis Pages: 31
LevelOne FPC-0103T Manual preview
FPC-0103T
Brand: LevelOne Pages: 31
HARTING HAIIC MICA Hardware Development Manual preview
HAIIC MICA
Brand: HARTING Pages: 13
National Instruments NI WLS/ENET-9163 User Manual preview
NI WLS/ENET-9163
Brand: National Instruments Pages: 36
janitza Procont LMC-008-IO User Manual And Technical Data preview
Procont LMC-008-IO
Brand: janitza Pages: 28
TVT Digital TD-3316B4-16P-A1 Quick Start Manual preview
TD-3316B4-16P-A1
Brand: TVT Digital Pages: 2
Qlogic Storage Networking (Unified Fabric Pilot) Installation Manual preview
Storage Networking (Unified Fabric Pilot)
Brand: Qlogic Pages: 76
Supersonic Franky Instruction Manual preview
Franky
Brand: Supersonic Pages: 46
DigiTech RPX400 Troubleshooting Manual preview
RPX400
Brand: DigiTech Pages: 6
Comway 4G DTU Configuration Instructions preview
4G DTU
Brand: Comway Pages: 20
Cypress Semiconductor CY7C1303BV25 Specification Sheet preview
CY7C1303BV25
Brand: Cypress Semiconductor Pages: 19
Accusys ACS-7630 User Manual preview
ACS-7630
Brand: Accusys Pages: 34
Aviosys 9255W User Manual preview
9255W
Brand: Aviosys Pages: 77
ADTRAN Total Access 1500 Dual FXS/DPO Quick Start Manual preview
Total Access 1500 Dual FXS/DPO
Brand: ADTRAN Pages: 2

Brands by name

Popular brands

Load more brands