GigaDevice Semiconductor GD32L23 Series User Manual Download Page 184

Page: 184 / 639

GD32L23x User Manual

184

Set and configure the DMA channel x completely, except enabling the channel x.

Set and configure the related DMAMUX channel y completely.

Configure the CHEN bit with ‘1’ in the DMA_CHxCTL register to enable the DMA channel

11.5.4.

Interrupt

There are two types of interrupt event, including synchronization overrun event on each

DMAMUX request multiplexer channel, and trigger overrun event on each DMAMUX request

generator channel.

Each interrupt event has a dedicated flag bit, a dedicated clear bit, and a dedicated enable

bit. The relationship is described in the following

Table 11-1. Interrupt events

Interrupt event

Flag bit

Clear bit

Enable bit

Synchronization overrun event

on DMAMUX request multiplexer

channel x

SOIFx in

DMAMUX_RM_INTF

SOIFCx in

DMAMUX_RM_INTC

SOIE in

DMAMUX_RM_CH

xCFG register

Trigger overrun event on

DMAMUX request generator

channel y

TOIFy in

DMAMUX_RG_INTF

TOIFCy in

DMAMUX_RG_INTC

TOIE in

DMAMUX_RG_CH

xCFG register

Trigger overrun interrupt

When the DMAMUX request trigger overrun flag TOIFx is set, and the trigger overrun interrupt

is enabled by setting TOIE bit, a trigger overrun interrupt will be generated. The overrun flag

TOIFx is reset by writing 1 to the corresponding clear bit of overrun flag TOIFCx in the

DMAMUX_RG_INTC register.

Synchronization overrun interrupt

When the synchronization overrun flag SOIFx is set, and the synchronization overrun interrupt

is enabled by setting SOIE bit, a synchronization overrun interrupt will be generated. The

overrun flag SOIFx is reset by writing 1 to the corresponding clear bit of synchronization

overrun flag bit SOIFCx in the DMAMUX_RM_INTC register.

11.5.5.

DMAMUX mapping

Request multiplexer input mapping

A DMA request is sourced either from the peripherals or from the DMAMUX request generator,

the sources can refer to

Table 11-2. Request multiplexer input mapping

, configured by the

MUXID[5:0] bits in the DMAMUX_RM_CHxCFG register for the DMAMUX request multiplexer

channel x.

Summary of Contents for GD32L23 Series
































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for GD32L23 Series

Reviews:

Brands by name

Popular brands

GigaDevice Semiconductor GD32L23 Series, User Manual

Search results

Summary of Contents for GD32L23 Series

Reviews:

Brands by name

Popular brands