Motherboard Components/
主板组件
No.
Code
Description
1 SW_ID
ID switch button w/LED
2
QSFP_3
QSFP LAN port #3 (left)
QSFP_2
QSFP LAN port #2 (middle)
QSFP_1
QSFP LAN port #1 (right)
3
SFP+_0_3
SFP+ connectors #0~#3
4
USB3_MLAN
BMC Management LAN port (top) / USB 3.0 ports (bottom)
5
COM1_VGA
Serial port (top)/VGA port(bottom)
6
PMBUS
PMBus connector
7
ATX1
24 pin power cponnector
8
F_USB3
USB 3.0 header
9
P12V_AUX2
8 pin power connector (for secondary CPU)
10
P12V_AUX1
8 pin power connector (for primary CPU)
11
MINI_CN0
Mini-SAS connector#0 supports SATA3 6Gb/s
12
MINI_CN1
Mini-SAS connector#1 supports SATA3 6Gb/s
13
BAT
Battery socket
14
DIMM_P0_B0
Channel 2 slot 0 (for primary CPU)
15
DIMM_P0_B1
Channel 2 slot 1 (for primary CPU)
16
DIMM_P0_D0
Channel 4 slot 0 (for primary CPU)
17
DIMM_P0_D1
Channel 4 slot 1 (for primary CPU)
18
CPU0
Cavium ThunderX CN88xx ARMv8 SoC processor (Primary CPU)
19
DIMM_P0_C1
Channel 3 slot 1 (for primary CPU)
20
DIMM_P0_C0
Channel 3 slot 0 (for primary CPU)
21
DIMM_P0_A1
Channel 1 slot 1 (for primary CPU)
22
DIMM_P0_A0
Channel 1 slot 0 (for primary CPU)
23
DIMM_P1_F0
Channel 2 slot 0 (for secondary CPU)
24
DIMM_P1_F1
Channel 2 slot 1 (for secondary CPU)
25
DIMM_P1_H0
Channel 4 slot 0 (for secondary CPU)
26
DIMM_P1_H1
Channel 4 slot 1 (for secondary CPU)
27
CPU1
Cavium ThunderX CN88xx ARMv8 SoC processor (Secondary CPU)
28
DIMM_P1_G1
Channel 3 slot 1 (for secondary CPU)
29
DIMM_P1_G0
Channel 3 slot 0 (for secondary CPU)
30
DIMM_P1_E1
Channel 1 slot 1 (for secondary CPU)
31
DIMM_P1_E0
Channel 1 slot 0 (for secondary CPU)
32
BP_1
HDD back plane board header
33
FP_1
Front panel header
34
MINI_CN4
Mini-SAS connector#4 supports SATA3 6Gb/s
35
MINI_CN5
Mini-SAS connector#5 supports SATA3 6Gb/s
36
MINI_CN6
Mini-SAS connector#6 supports SATA3 6Gb/s
37
MINI_CN7
Mini-SAS connector#7 supports SATA3 6Gb/s
No.
Code
Description
38
S3_MASK
S3 Power On Select Jumper
1-2 Close: Stop an initial power on when BMC
is not ready.
2-3 Close: Keep initial power on.
(Default setting)
39
BIOS_PWD
Clearing Supervisor Password jumper
1-2 Close: Normal operation. (Default setting)
2-3 Close: Skip supervisor password.
40
BIOS_RCVR
BIOS recovery jumper
1-2 Close: Normal operation. (Default setting)
2-3 Close: BIOS recovery mode.
41
COM2
Serial port cable connector
42
LAN Active LEDs
LAN Active LEDs
LAN3_ACT
LAN3 active LED (upper-left corner)
LAN4_ACT
LAN4 active LED (bottom-left corner)
LAN5_ACT
LAN5 active LED (upper-right corner)
LAN6_ACT
LAN6 active LED (bottom-right corner)
LAN7_ACT
LAN7 active LED (bottom-right corner)
43
CLR_CMOS
Clear CMOS jumper
1-2 Close: Normal operation (Default setting)
2-3 Close: Clear CMOS data.
44 IPMB
IPMB connector
45
BUZZER
Buzzer
46
PCIE_5
PCI Express x8 slot
47
PCIE_4
PCI Express x8 slot
48
PCIE_3
PCI Express x8 slot
49
MINI_CN3
Mini-SAS connector#3 supports SATA3 6Gb/s
50
MINI_CN2
Mini-SAS connector#2 supports SATA3 6Gb/s
51
PCIE_2
PCI Express x16 slot
52
LED_BMC
BMC firmware readiness LED
1
2
3
4
7
5
6
8
9
10
11
12
13
14
15
16
17
19
20
21
22
23
24
25
26
28
29
30
31
32
33
38
42
37
36
35
34
39
40
41 43 44
45
52
46 47 48
49
50
51
18
27
No
Description
1
HDD#0
2
HDD#1
3
HDD#2
4
HDD#3
5
HDD#4
6
HDD#5
7
HDD#6
8
HDD#7
9
HDD#8
10
HDD#9
11
HDD#10
12
HDD#11
13
HDD#12
R270-T60
R270-T61
No
Description
14
HDD#13
15
HDD#14
16
HDD#15
17
HDD#16
18
HDD#17
19
HDD#18
20
HDD#19
21
HDD#20
22
HDD#21
23
HDD#22
24
HDD#23
25
Fan connector#1_A
26
Fan connector#1_B
No
Description
1
HDD#0
2
HDD#1
3
HDD#2
4
HDD#3
5
HDD#4
6
HDD#5
7
HDD#6
No
Description
8
HDD#7
9
HDD#8
10
HDD#9
11
HDD#10
12
HDD#11
13
Fan connector#1_A
14
Fan connector#1_B
No
Description
27
Fan connector#2_A
28
Fan connector#2_B
29
Fan connector#3_A
30
Fan connector#3_B
31
Fan connector#4_A
32
Fan connector#4_B
33 SGPIO1
34 SGPIO2
35 SGPIO3
36 SGPIO4
37 SGPIO5
38 SGPIO6
CAUTION!
Before you remove or install the system cover:
Make sure the system is not turned on or connected to AC power.
注意！
在卸下或安装系统机盖之前，请注意下列事项：
确保系统未开启且未连接到交流电源。
System Components/
系统组件
No
Description
1
HDD bays
2
System fan #1 (FAN1_A/FAN1_B)
3
System fan #2 (FAN2_A/FAN2_B)
4
System fan #3 (FAN3_A/FAN3_B)
5
System fan #4 (FAN4_A/FAN4_B)
6
Memory slots
7
CPU heat sink
8
PCIe riser slots
9
Power supply cage
No
Description
1
HDD bays
2
System fan #1 (FAN1_A/FAN1_B)
3
System fan #2 (FAN2_A/FAN2_B)
4
System fan #3 (FAN3_A/FAN3_B)
5
System fan #4 (FAN4_A/FAN4_B)
6
Memory slots
7
CPU heat sink
8
PCIe riser slots
9
Power supply cage
CAUTION!
To connect system fan connector, follow the instruction:
Blue/Red cable connect to odd numbered connector.
White/Amber cable connect to even numbered connector.
CAUTION!
Remove fan duct before installing the CPU heat sinks.
注意！
蓝/红电缆连连接于单数风扇插座。
白/橘电缆连连接于双数风扇插座。
No
Description
15
Fan connector#2_A
16
Fan connector#2_B
17
Fan connector#3_A
18
Fan connector#3_B
19
Fan connector#4_A
20
Fan connector#4_A
21 SGPIO1
1
2
3
4
5
6
7
7
8
9
6
6
1
2
3
4
5
6
7
7
8
9
6
6
No
Description
22 SGPIO2
23 SGPIO3
Front Panel Header/
前面板接头
No.
Pin Define
1
Power LED+
3
No Pin
5
Power LED-
7
HDD LED+
9
HDD LED-
11
Power Button
13 GND
15
Reset
17 GND
19
ID
21
ID Switch-
23
NMI Switch-
No.
Pin Define
2
5V Standby
4
ID LED+
6
ID LED-
8
System Front Board LED+
10
System Status LED-
12
LAN1 Active LED+
14
LAN1 Link LED-
16
SMBus Data
18
SMBus Clock
20
Case Open
22
LAN2 Active LED
24
LAN2 Link LED-
1
2423
2
HDD Back Plane Board Header/
硬盘驱动器底板接头
1 2
25 26
No.
Pin Define
1
BP_SGP_CLK
3
BP_SGP_GLD
5
BP_SGP_DOUT
7
Key Pin
9 GND
11
BP_LED_G_N
13 BP_SGP_DIN
15 GND
17 GND
19
P_3V3_AUX
21
P_3V3_AUX
23 GND
25
BP_PRESENSE
No.
Pin Define
2
No Connect
4
FAN_SGP_Gate
6 GND
8
Reset
10
BP_LED_A_N
12 GND
14
No Connect
16
SMB_BP_DATA
18
SMB_BP_CLK
20
BMC_ACK
22
BMC_REQ
24
Key Pin
26 GND
R270-T61
R270-T60
System Cover/
机箱盖
1
2
3
1
3
1
4
5
1
2
3
1
3
1
4
5
CAUTION!
To remove fan duct, follow the instruction:
1. CPU0: Remove the secruing screw, lift system fan slightly, then remove the fan duct.
2. CPU1: Remove the secruing screws of supporting bracket, lift system fan slightly,
then remove the fan duct.
R270-T60
R270-T61
Fan Duct/
风扇散热片
1
2
4
3
1
2
4
3
注意！
1. CPU0: 移除导风罩上的螺丝并将风扇轻轻往上拉即可移除导风罩。
2.
CPU1: 移除铁片上的螺丝并移除铁片，将风扇轻轻往上拉即可移除导风罩。
R270-T61
R270-T60
1
Heat Sink/
散热装置
注意！
安装散热装置前请先移除导风罩。
System Front View
R270-T60
System Front View
R270-T61
System Rear View
Memory Population Configuration/
安装内存
4
1
2
3
Rank(s)
1 Rank
2 Rank
x8,x16
x8,x16
1 Rank
2 Rank
x8,x16
x8,x16
8
8,16
8
8,16
Data Width
Per DIMM Capacity (GB)
1600MTS
1866MTS
2133MTS
1 DIMM per channel
2 DIMM per channel
#DIMM per channel
DDR4 UDIMM Configuration
Rank(s)
1 Rank
x4
8,16
x8
4,8
2 Rank
x4
16,32
x8
8,16
1 Rank
x4
8,16
x8
4,8
2 Rank
x4
16,32
x8
8,16
Data Width
Per DIMM Capacity (GB)
1600MTS
1866MTS
2133MTS
1 DIMM per channel
2 DIMM per channel
#DIMM per channel
DDR4 RDIMM Configuration
DIMM must be populated starting from DIMM_P0_A0/DIMM_P0_B0 socket and must be installed in
matched pairs.
One CPU only supports the population of 2/4 (1DPC)/8 (2DPC) in the same time.
System will not boot normally with incorrect populated sequence.
DIMM必须从DDR3_P0_A0//DIMM_P0_B0插槽开始按顺序安装。DIMM必须成对安装。
只能支持一個CPU同時上2/4 (1DPC)/8(2DPC)數量的DIMM。
若安装顺序有误，系统将无法正常开机。
R270-T61
R270-T60
System Fan/
系统风扇
注意！
确保系统未开机且未连接到交流电源。
断开所有必要的线缆连接。若不遵循这些警告，可能造成人员伤害或设备损坏。
CAUTION!
Before you remove or install the system fan:
Make sure the system is not turned on or connected to the AC power.
Disconnect all necessary cable connections. Failure to observe these warnings could result in
personal injury or damage to the equipment.
R270-T60 HDD Backplane Board Components
R270-T61 HDD Backplane Board Components
Hard Disk Drive and Back Plane Board/
硬盘驱动器与硬盘驱动器底板
1
2
3
4
4
2
1
3
4
4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
33
34
35
36
37
38
26
27
28
29
30
31
32
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
No.
Description
1
Power button w/LED
2
Front panle LEDs and buttons
3
ID button w/LED
4
HDD bays
No.
Description
1
Power button w/LED
2
Front panle LEDs and buttons
3
ID button w/LED
4
HDD bays
No
Description
1
Power supply fan
2
Power supply module cord socket
3
VGA port
4
Serial port
5
KVM Server Management 10/100/1000 LAN port
6
USB 3.0 ports
7
SFP+ LAN ports
8
QSFP+ LAN ports
9
ID switch button w/LED
10
Low-profle half-length card
Front & Rear/
系统前部与后部概览
Off
State
Description
Yellow On
1Gbps data rate
Green On
100Mbps data rate
10Mbps data rate
Speed LED Link/Activity
LED
1
2
3
4
3 4 5
10
7
6
8 9
1
2
State
Description
Green On
40 Gbps data rate
Yellow On
10 Gbps data rate
QSFP+ LAN LED:
State
Description
Yellow On
1 Gbps data rate
Green On
10 Gbps data rate
SFP+ LAN LED:
State
Description
Green On
Link between system
and network
Blink
LAN is active
Link/Activity LED:
R270-T61
R270-T60
PCI Express Card/
PCI Express 扩展卡
注意！
在安装扩展卡前，请注意下列事项：
确保系统未开启且未连接到交流电源。
CAUTION!
Before you remove or install the PCI express card:
Make sure the system is not turned on or connected
to AC power.
1
3
2
1
3
2
注意！
在替换或安装电源前，请注意下列事项：
确保系统未开启且未连接到交流电源。
CAUTION!
Before you remove or install the power supplies:
Make sure the system is not turned on or connected to AC power.
Power Supply/
电源
1
3
2
Front Panel LED and Buttons/
前面板 LED 说明
1
2
3
4
5
6
7
Rail Kit/
导轨
Release
Lock out
⯮ⅎ庳⎽⇡
Release and detach the inner member from the slide
1
M4X6
Click
Aach the unit to the inner member
⯭Ⅼ彏擨ᷱ㜡⏗
2
Bracket
M6X13
M6-NUT
Fix the outer member/bracket assembly to the frame
⯭⣽彏㈿㞝擨⅌㜡㞝
3
Release
lock in
Insert the unit to complete the installaon
墬⅌㜡㞝
4
说明
2
按下按钮启动系统识别功能。
ID按钮
LED
1
系统处于开机状态。
系统未开机或处于ACPIS5状态（关机状态）。
系统处于ACPI S4状态（休眠模式）。
电源按钮和LED
绿色
恒亮
蓝色
恒亮
不亮
无亮灯
3/4
恒亮
系统和网络之间的链接
绿色
不亮
断开连接/待机
无亮灯
LAN1/LAN2活动LED
编号
名称
颜色
状态
7
复位按钮
按此按钮启动系统。
5
硬盘驱动器定位
硬盘驱动器访问
硬盘驱动器故障
硬盘重建
无硬盘驱动器访问
绿色
橙色
绿色/橙色
不亮
亮
亮
闪烁
无亮灯
硬盘驱动器LED
闪烁
6
系统正常运行
。
橙色
绿色
系统状态LED
恒亮
恒亮
不亮
闪烁
无亮灯
严重情形，可能为下列状况：
电源模块故障
系统风扇故障
电源电压问题
系统温度/电压问题
非严重情形，可能为下列状况：
冗余电源模块故障
系统温度/电压问题
机箱侵入
系统未正常运行，可能为下列状况：
POST错误
NMI错误
处理器或终结器缺失
No.
Name
Color
Status
Description
2
Press the button to activate system identifcation.
ID Button and LED
1
System is powered on.
System is not powered on or in ACPI S5 state (power off).
System is in ACPI S4 state (hibernate mode).
Power Button and LED
Green
Green
Solid On
Blue
Solid On
Off
N/A
3/4
Link between system and network.
Solid On
No data transmission or receiving is occurring.
Off
N/A
LAN1/2 Active/Link LEDs
5
7
Reset Button
Press the button to reset the system.
HDD locate
HDD access
HDD fault
HDD rebuild
No HDD access or no HDD fault
Green
Amber
Green/Amber
On
Off
Blink
On
Blink
N/A
HDD Status LED
6
System is operating normally.
System Status LED
Green
Amber
Solid On
Critical condition, may indicates:
Power module failure
System fan failure
Power supply voltage issue
System temperature
Solid On
Non-critical condition, may indicates:
Redundant power module failure
Temperature and voltage issue
Chassis intrusion
System is not ready, may indicates:
POST error
NMI error
Processor or terminator missing
Blink
N/A
N/A
R270-T60/R270-T61 Quick Installation Guide/R270-T60/R270-T61
速安装说明
10/100/1000 LAN LED:
Description
ID button/LED:
Blue On
System identifcation
is active.
Off
System identifcation
is disabled.
State
SpeedLED
Link/Activity
LED
Power button/LED:
Green On
Off
Description
System is powered on
System is powered off
State
Link/Activity LED
Speed LED
PN:25ME0-R27000-CLR