Gigabyte R181-340 Service Manual Download Page 109

Page: 109 / 127

- 109 -

BIOS Setup

5-4-4

IPv6 BMC Network Configuration

IPv6 BMC Lan Channel 1
IPv6 BMC Lan Option

Enable/Disable IPv6 BMC LAN channel function. When this item is disabled, the system will not modify

any BMC network during BIOS phase.

Options available: Enable/Disable. Default setting is

Enable

IPv6 BMC Lan IP Address Source

Select to configure LAN channel parameters statically or dynamically (by BIOS or BMC).

Options available: Unspecified/Static/Dynamic-Obtained by BMC running DHCP.

Default setting is

Dynamic-Obtained by BMC running DHCP

IPv6 BMC Lan IP Address/Prefix Length -> [1999::11/64]

Check if the IPv6 BMC LAN IP address matches those displayed on the screen.

Summary of Contents for R181-340
































































































































Search results

Summary of Contents for R181-340

Reviews:

Related manuals for R181-340

Brands by name

Popular brands

Gigabyte R181-340, Service Manual

Search results

Summary of Contents for R181-340

Reviews:

Related manuals for R181-340

Brands by name

Popular brands