Gigabyte GN-AP03G User Manual Download Page 24

GN-AP03G AirCruiser G Range Extender 

Chapter 4 Troubleshooting 

 

This chapter gives information about troubleshooting your AirCruiser G Range Extender. Read the 
descriptions below for assistance is diagnosing and solving the problem. 
 

Q:  What to do if you forget your password or forget the IP address of the Range Extender? 
A:  

Please press and hold for 5 seconds the 

“init”

 button at the bottom of the Range Extender. The 

Access Point will be reset to the factory default values, and the password will be restored to factory 
default. 

 

Q:  I am unable to connect to the Internet. 
A: 

1. 

Confirm that the power cord is connected properly and the Range Extender’s power LED is 
correctly lit. 

 

2. 

Check whether all of the settings described in this manual are correctly set. 

 

3. 

Verify that your ADSL/Cable Modem is operating normally, and/or you have ISP service 
available. 

 

4. 

Check that your network cable is connected correctly, and the LED status is normal. 

 

Q:  I am unable to access the Range Extender’s Web Configuration Interface. 
A: 

1. 

Please check the Ethernet connection (RJ-45 LAN cable) between the PC and the Range 
Extender is properly connected. 

 

2. 

Make sure your computer’s IP address is on the same subnet as the Range Extender. (Check 
this by typing “

ipconfig /all” 

from a DOS command prompt) 

 

3. 

Make sure you are carefully typing the correct IP address of the Range Extender in the address 
bar of your web browser. The IP address of your Range Extender is the “Gateway” address you 
see when you run the “

ipconfig /all”

 command. 

 

4.    Try initializing your router to factory settings.     

 

Q:  What is the IEEE 802.11b standard? 
A:

  It is also referred to as 802.11 High Rate or Wi-Fi. It is an expansion to 802.11 that applies to wireless 

LAN and provides 11 Mbps transmission (with a fallback to 5.5, 2 and 1 Mbps) in the 2.4 GHz band. 
The 802.11b uses only Direct Sequence Spread Spectrum (DSSS). The 802.11b was a 1999 
ratification to the origianl 802.11 standard, allowing wireless functionality comparable to Ethernet. 

 

Q:  What is WEP? 
A: 

Wired Equivalent Privacy (WEP). A security mechanism defined within the 802.11 standard and 
designed to make the link integrity of the wireless medium equal to wired cable. 

 

Q:  What is the IEEE 802.11g standard? 
A:  

IEEE 802.11g standard specifies data rates of up to 54 Mbps in the 2.45-GHz band. It uses 
Orthogonal Frequency Division Multiplexing (OFDM), which is the mandatory provisions have been 
made within the standard to make it inherently compatible with the well-established 802.11b standard 
at 11 Mbps, which uses Complementary Code Keying (CCK) modulation. Both .11g and .11b can 
operate at ranges of up to 300 feet. 

20 

Summary of Contents for GN-AP03G





































Reviews: