manualshive.com logo in svg

Gigabyte GA-MA790GP-UD3H, User Manual, Page: 50 / 104

Share
Download
Gigabyte GA-MA790GP-UD3H User Manual Download Page 50

GA-MA790GP-UD3H Motherboard

- 50 -

SMART LAN (LAN Cable Diagnostic Function)

CMOS Setup Utility-Copyright (C) 1984-2009 Award Software

SMART LAN

Item Help

Menu Level

Start detecting at Port.....
Part1-2 Status =

Open

/ Length

=

0m

Part3-6 Status =

Open

/ Length

=

0m

Part4-5 Status =

Open

/ Length

=

0m

Part7-8 Status =

Open

/ Length

=

0m



: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

F5: Previous Values

F6: Fail-Safe Defaults

F7: Optimized Defaults

This motherboard incorporates cable diagnostic feature designed to detect the status of the attached LAN
cable.  This feature will detect cabling issue and report the approximate distance to the fault or short.
Refer to the following information for diagnosing your LAN cable:

When No LAN Cable Is Attached...

If no LAN cable is attached to the motherboard, the 

Status

 fields of all four pairs of wires will show

Open

 and the 

Length 

fields show 

0m

, 

 

as shown in the figure above.

Start detecting at Port.....
Link Detected --> 100Mbps
Cable Length= 30m

When LAN Cable Is Functioning Normally...

If no cable problem is detected on the LAN cable connected to a Gigabit hub or a 10/100 Mbps hub,
the following message will appear:

Onboard LAN Function

Enables or disables the onboard LAN function. (Default: Enabled)
If you wish to install a 3rd party add-in network card instead of using the onboard LAN, set this item
to 

Disabled

.

Link Detected

Displays transmission speed

Cable Length

Displays the approximate length of the attached LAN cable.

Note: The Gigabit hub will only operate at a speed of 10/100 Mbps in MS-DOS mode; it will operate
at a normal speed of 10/100/1000 Mbps in Windows mode or when the LAN Boot ROM is
activated.

When a Cable Problem Occurs...

If a cable problem occurs on a specified pair of wires, the 

Status 

field will show 

Short

 and

thenlength shown will be the approximate distance to the fault or short.
Example: 

Part1-2 Status = Short / Length  =  2m

Explanation: A fault or short might occur at about 2m on Part 1-2.

Note: Part 4-5 and Part 7-8 are not used in a 10/100 Mbps environment, so their

 Status

 fields will

show 

Open

, and the length shown is the approximate length of the attached LAN cable.

Summary of Contents for GA-MA790GP-UD3H









































































































Reviews:

No comments