manualshive.com logo in svg

Gigabyte GA-H55M-USB3, User Manual, Page: 51 / 128

Share
Download
Gigabyte GA-H55M-USB3 User Manual Download Page 51

- 51 -

BIOS Setup

  USB Controllers

 

Enables or disables the integrated USB controllers. (Default: Enabled)

 

Disabled

 will turn off all of the USB functionalities below.

  USB Legacy Function

 

Allows USB keyboard to be used in MS-DOS. (Default: Enabled)

  USB Storage Function

 

Determines whether to detect USB storage devices, including USB flash drives and USB hard drives 

during the POST. (Default: Enabled)

  Azalia Codec

 

Enables or disables the onboard audio function. (Default: Auto)

 

If you wish to install a 3rd party add-in audio card instead of using the onboard audio, set this item to 

Disabled

.

  Onboard H/W 1394

 

Enables or disables the onboard IEEE 1394 function. (Default: Enabled)

  Onboard H/W LAN

 

Enables or disables the onboard LAN function. (Default: Enabled)

 

If you wish to install a 3rd party add-in network card instead of using the onboard LAN, set this item to 

Disabled

.

  Green LAN

 

When the onboard LAN function and 

Green LAN

 are enabled, the system will dynamically detect if a 

LAN cable is connected or not. If not, the corresponding LAN controller will be disabled automatically. 
(Default: Disabled)

CMOS Setup Utility-Copyright (C) 1984-2010 Award Software

SMART LAN

  Start detecting at Port.....

  Part1-2  Status  =  Open    /  Length  =      0m

  Part3-6  Status  =  Open    /  Length  =      0m

  Part4-5  Status  =  Open     /  Length  =      0m

  Part7-8  Status  =  Open    /  Length  =      0m

higf

: Move 

Enter: Select 

+/-/PU/PD: Value 

F10: Save 

ESC: Exit 

F1: General Help

 

F5: Previous Values 

F6: Fail-Safe Defaults   

F7: Optimized Defaults

Item Help

Menu Level

 

  SMART LAN

This motherboard incorporates cable diagnostic feature designed to detect the status of the attached LAN 
cable. This feature will detect cabling issue and report the approximate distance to the fault or short.  Refer to 
the following information for diagnosing your LAN cable:

  When No LAN Cable Is Attached...

 

If no LAN cable is attached to the motherboard, the 

Status fields of all four pairs of wires will show Open

 

and the 

Length fields show 0m, as shown in the figure above.

Summary of Contents for GA-H55M-USB3

































































































































Reviews:

No comments