manualshive.com logo in svg

Gigabyte GA-8I945PL-G, User Manual

Share
Download
Gigabyte GA-8I945PL-G User Manual Download Page 21

Hardware Installation

- 21 -

English

6) IDE1/IDE2/IDE3 (IDE Connector)

An IDE device connects to the computer via an IDE connector. One IDE connector can connect to one
IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical drive).
If you wish to connect two IDE devices, please set the jumper on one IDE device as Master and the
other as Slave (for information on settings, please refer to the instructions located on the IDE
device). To ensure that an IDE CD-ROM drive can work properly, please attach it to the IDE 1
connector.

1

2

39

40

7) SATAII0/SATAII1/SATAII2/SATAII3 (SATA 3Gb/s Connector)

SATA 3Gb/s can provide up to 300MB/s transfer rate. Please refer to the BIOS setting for the
Serial ATA II and install the proper driver in order to work properly.

Pin No.

Definition

1

GND

2

TXP

3

TXN

4

GND

5

RXN

6

RXP

7

GND

1

7

1

7

Summary of Contents for GA-8I945PL-G

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands