Gigabyte GA-8I945GZME-RH User Manual Download Page 21 | Manualshive

Page: 21 / 80

background image

Hardware Installation

- 21 -

English

6) FDD (FDD Connector)

The FDD connector is used to connect the FDD cable while the other end of the cable connects to
the FDD drive. The types of FDD drives supported are: 360KB, 720KB, 1.2MB, 1.44MB and
2.88MB. Before attaching the FDD cable, please take note of the foolproof groove in the FDD
connector.

1

2

33

34

Pin No.

Definition

1

GND

2

TXP

3

TXN

4

GND

5

RXN

6

RXP

7

GND

7) SATAII0 / SATAII1 / SATAII2 / SATAII3 (SATA 3Gb/s Connectors)

SATA 3Gb/s can provide up to 300MB/s transfer rate. Please refer to the BIOS setting for the
SATA 3Gb/s and install the proper driver in order to work properly.

7

1

1

7

SATAII1

SATAII0

7

1

1

7

SATAII3

SATAII2

«
...
19
20
21
22
23
...
»

Summary of Contents for GA-8I945GZME-RH

















































































Reviews:

No comments

Related manuals for GA-8I945GZME-RH

Brand: ASROCK Pages: 80

Brand: Texas Instruments Pages: 18

Brand: EVGA Pages: 2

Brand: JETWAY Pages: 57

ISL70321SEHDEMO1Z

Brand: Intersil Pages: 9

Brand: ON Semiconductor Pages: 8

Brand: Linear Pages: 16

Brand: Icop Pages: 31

dsPICDEM MCHV-3

Brand: Microchip Technology Pages: 68

Brand: K&B Pages: 6

Brand: ECS Pages: 87

Brand: Advantech Pages: 136

Brand: ECS Pages: 131

Brand: ON Semiconductor Pages: 5

STEALTH 54LB/48

Brand: Watersnake Pages: 52

Brand: TYAN Pages: 35

Brand: TYAN Pages: 58

Brand: TYAN Pages: 67

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands