manualshive.com logo in svg

Gigabyte GA-5EXSH-RH, User Manual

Share
Download
Gigabyte GA-5EXSH-RH User Manual Download Page 38

3 8

GA-5EXSH-RH Motherboard

Serial Port A

 This allows users to configure serial prot A  by using this option.

Enabled

 Enable the configuration (Default setting)

Disabled

 Disable the configuration.

 

Base I/O Address/IRQ

3F8

Set IO address to 3F8.    (Default setting)

2F8

Set IO address to 2F8.

3E8

Set IO address to 3E8.

2E8

Set IO address to 2E8.

Serial Port B

This allows users to configure serial prot B  by using this option.

Enabled

 Enable the configuration

Disabled

 Disable the configuration.(Default setting)

 

Base I/O Address/IRQ

3F8

Set IO address to 3F8.

2F8

Set IO address to 2F8.  (Default setting)

3E8

Set IO address to 3E8.

2E8

Set IO address to 2E8.

Parallel Port

 This allows users to configure parallel port  by using this option.

Enabled

 Enable the configuration.

Disabled

 Disable the configuration. (Default setting)

 

Mode

This option allows user to set Parallel Port transfer mode.

Bi-directional Use this setting to support bi-directional transfers on the parallel

port. (Default setting)

Summary of Contents for GA-5EXSH-RH

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands