Gigabyte G492-Z51 User Manual Download Page 78

Page: 78 / 117

BIOS Setup

- 78 -

5-2-18

MAC IPv4 Network Configuration

Parameter

Description

Configured

Indicates whether network address is configured successfully or not.

Options available: Disabled/Enabled. Default setting is

Disabled

Enable DHCP

(Note)

Options available: Enabled/Disabled. Default setting is

Enabled

Local IP Address

(Note)

Press [Enter] to configure local IP address.

Local NetMask

(Note)

Press [Enter] to configure local NetMask.

Local Gateway

(Note)

Press [Enter] to configure local Gateway

Local DNS Servers

(Note)

Press [Enter] to configure local DNS servers

Save Changes and Exit

Press [Enter] and then choose to save or discard the changes made.

(Note) This item will appear on the screen when

Configured

is set to

Enabled

Summary of Contents for G492-Z51






















































































































Search results

Summary of Contents for G492-Z51

Reviews:

Related manuals for G492-Z51

Brands by name

Popular brands

Gigabyte G492-Z51, User Manual

Search results

Summary of Contents for G492-Z51

Reviews:

Related manuals for G492-Z51

Brands by name

Popular brands