Gigabyte G492-Z51 User Manual Download Page 77

Page: 77 / 117

- 77 -

BIOS Setup

5-2-17

VLAN Configuration

Parameter

Description

Enter Configuration Menu

Press [Enter] to configure advanced items.

Create new VLAN

VLAN ID

– Sets VLAN ID for a new VLAN or an existing VLAN.

– Press the <+> / <-> keys to increase or decrease the desired values.

The valid range is from 0 to 4094.

Priority

– Sets 802.1Q Priority for a new VLAN or an existing VLAN.

– Press the <+> / <-> keys to increase or decrease the desired values.

The valid range is from 0 to 7.

Add VLAN

– Press [Enter] to create a new VLAN or update an existing VLAN.

Configured VLAN List

– Enable/Disable the VLAN.

– Options available: Enable/Disable. Default setting is

Disabled

Remove VLAN

– Press [Enter] to remove an existing VLAN.

Summary of Contents for G492-Z51






















































































































Search results

Summary of Contents for G492-Z51

Reviews:

Related manuals for G492-Z51

Brands by name

Popular brands

Gigabyte G492-Z51, User Manual

Search results

Summary of Contents for G492-Z51

Reviews:

Related manuals for G492-Z51

Brands by name

Popular brands