Gigabyte G492-Z51 User Manual Download Page 107

Page: 107 / 117

- 107 -

BIOS Setup

5-6-3

BMC Network Configuration

Parameter

Description

BMC network configuration

Lan Channel 1

Configuration Address source

Select to configure LAN channel parameters statically or dynamically

(DHCP). Do nothing option will not modify any BMC network parameters
during BIOS phase.

Options available: Unspecified/Static/DynamicBmcDhcp. Default setting is

DynamicBmcDhcp

Station IP address

Displays IP Address information.

Subnet mask

Displays Subnet Mask information.

Router IP address

Displays the Router IP Address information.

Station MAC address

Displays the MAC Address information.

Real-time synchronize BMC
network parameter values

Press [Enter] to synchronize the BMC network parameter values.

Summary of Contents for G492-Z51






















































































































Search results

Summary of Contents for G492-Z51

Reviews:

Related manuals for G492-Z51

Brands by name

Popular brands

Gigabyte G492-Z51, User Manual

Search results

Summary of Contents for G492-Z51

Reviews:

Related manuals for G492-Z51

Brands by name

Popular brands