Gigabyte G492-Z51 User Manual Download Page 103

Page: 103 / 117

- 103 -

BIOS Setup

5-6 Server Management Menu

Parameter

Description

FRB-2 Timer

FRB-2 timer (POST timer).

FRB-2 Timer
timeout

Configure the FRB2 Timer timeout.

Options available: 3 minutes/4 minutes/5 minutes/6 minutes. Default setting is

minutes

(NOTE) This item is configurable when FRB-2 Timer is set to Enabled.

FRB-2 Timer Policy

Configure the FRB2 Timer policy.

Options available: Do Nothing/Reset/Power Down. Default setting is

Do Nothing

(NOTE ) This item is configurable when FRB-2 Timer is set to Enabled.

OS Watchdog Timer

Enable/Disable OS Watchdog Timer function.
Options available: Enabled/Disabled. Default setting is

Disabled

OS Wtd Timer
Timeout

Configure OS Watchdog Timer.

Options available: 5 minutes/10 minutes/15 minutes/20 minutes. Default setting is

minutes

(NOTE) This item is configurable when OS Watchdog Timer is set to Enabled.

OS Wtd Timer
Policy

Configure OS Watchdog Timer Policy.

Options available: Reset/Do Nothing/Power Down. Default setting is

Reset

(NOTE) This item is configurable when OS Watchdog Timer is set to Enabled.

Wait BMC Ready

Configure time to wait BMC ready.

Options available: Disabled/2 minutes/4 minutes/6 minutes. Default setting is

minutes

System Event Log

Press [Enter] to configure advanced items.

Summary of Contents for G492-Z51






















































































































Search results

Summary of Contents for G492-Z51

Reviews:

Related manuals for G492-Z51

Brands by name

Popular brands

Gigabyte G492-Z51, User Manual

Search results

Summary of Contents for G492-Z51

Reviews:

Related manuals for G492-Z51

Brands by name

Popular brands