Gigabyte G242-Z12 User Manual Download Page 81

Page: 81 / 141

- 81 -

BIOS Setup

5-2-18

MAC IPv4 Network Configuration

Parameter

Description

Configured

Indicates whether network address is configured successfully or not.

Options available: Enabled/Disabled. Default setting is

Disabled.

Enable DHCP

(Note)

Options available: Enabled/Disabled. Default setting is

Enabled.

Local IP Address

(Note)

Press [Enter] to configure local IP address.

Local NetMask

(Note)

Press [Enter] to configure local NetMask.

Local Gateway

(Note)

Press [Enter] to configure local Gateway

Local DNS Servers

(Note)

Press [Enter] to configure local DNS servers

Save Changes and Exit

Press [Enter] to save all configurations.

(Note) This item appears when

Configured

is set to

Enabled

Summary of Contents for G242-Z12














































































































































Search results

Summary of Contents for G242-Z12

Reviews:

Related manuals for G242-Z12

Brands by name

Popular brands

Gigabyte G242-Z12, User Manual

Search results

Summary of Contents for G242-Z12

Reviews:

Related manuals for G242-Z12

Brands by name

Popular brands