manualshive.com logo in svg

Giga-tronics GT-1000B, Operation Manual, Page: 17 / 26

Share
Download
Giga-tronics GT-1000B Operation Manual Download Page 17

Giga-tronics GT-1000B Microwave Power Amplifier   

Operation 

Operation Manual, Part Number 34672-001, Rev. A, May 2013 

Page 11 

Chapter 3

 

Operate the GT-1000B 

3.1

 

Operating Safety and Instructions 

This section describes how to operate the GT-1000B Microwave Power Amplifier. Equipment and personal 

safety information is also provided. 
 
 

DO NOT EXCEED AN INPUT LEVEL OF +17 dBm INTO THE GT-1000B. 

EXCEEDING THIS LEVEL CAN DAMAGE THE GT-1000B MICROWAVE POWER 

AMPLIFIER. 

 
 

WHEN ENERGIZED, THE GT-1000B IS CAPABLE OF SUPPLYING POWER THAT 

CAN CAUSE DAMAGE OR INJURY. TAKE THE FOLLOWING PRECAUTIONS TO 

ENSURE SAFE SETUP AND OPERATION:

 

•

 

Verify that all cables, connectors, and equipment connected to the GT-

1000B are in good condition.

 

•

 

Do not make connections to equipment while the output of any item of 

equipment is energized.

 

 
 

Table 6: Operate the GT-1000B 

Operate the GT-1000B 

Step 

Action 

1.

 

 Verify that the output of the signal source driving the amplifier is NOT energized before 

continuing to the next step. 

2.

 

 Connect the equipment to the GT-1000B according to your application. 

NOTE:

  Verify all mating connectors are 50 Ohm, and that they are in good condition. 

3.

 

 Apply AC power to the GT-1000B by turning the front panel power switch ON. Observe that the 

POWER ON indicator on the front panel illuminates (see Figure 1 on page 4) 

 

4.

 

 Verify that the output level of the signal source is set below +17 dBm. 

5.

 

 Energize the output of the signal source. 

6.

 

 

NOTE:

 The GT-1000B has a Remote RF Off input. This input may be used to enable or disable the 

RF output. Open circuit = RF On. Short circuit to ground = RF Off. 

7.

 

 

NOTE:

  Do not exceed the safe limits of the output power from the GT-1000B into the load. The 

load should be rated for at least 30 Watts CW. 

End of Procedure 

 
 

 

CAUTION 

         WARNING 

! 

Summary of Contents for GT-1000B



























Reviews:

No comments