GIGA-BYTE TECHNOLOGY MZ72-HB2 User Manual Download

Page: 120 / 124

- 120 -

BIOS Setup

2-8 Boot Menu

The Boot menu allows you to set the drive priority during system boot-up. BIOS setup will display an error

message if the legacy drive(s) specified is not bootable.

Parameter

Description

Boot Configuration

Setup Prompt Timeout

Number of seconds to wait for setup activation key. 65535 (0xFFFF)

means indefinite waiting.

Press the numeric keys to input the desired values.

Bootup NumLock State

Enable/Disable the Bootup NumLock function.
Options available: On, Off. Default setting is

Off

Quiet Boot

Enable/Disable showing the logo during POST.
Options available: Enabled, Disabled. Default setting is

Enabled

Setup Flash

Press [Enter] to run setup flash.

Dump full Setup Data

Press [Enter] to dump full setup data to file.

Dump non-default Setup Data

Press [Enter] to dump non-default setup data to file.

Restore Setup Data

Press [Enter] to restore setup data from file (cJson format).

Boot mode select

Selects the boot mode.
Options available: LEGACY, UEFI. Default setting is

UEFI

Summary of Contents for MZ72-HB2





























































































































Search results

Summary of Contents for MZ72-HB2

Reviews:

Related manuals for MZ72-HB2

Brands by name

Popular brands

GIGA-BYTE TECHNOLOGY MZ72-HB2, User Manual

Search results

Summary of Contents for MZ72-HB2

Reviews:

Related manuals for MZ72-HB2

Brands by name

Popular brands