manualshive.com logo in svg

GIGA-BYTE TECHNOLOGY GA-MA69VM-S2, User Manual

Share
Download
GIGA-BYTE TECHNOLOGY GA-MA69VM-S2 User Manual Download Page 21

Hardware Installation

- 21 -

English

6) IDE (IDE Connector)

An IDE device connects to the computer via an IDE connector. One IDE connector can connect to
one IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical
drive).  If you wish to connect two IDE devices, please set the jumper on one IDE device as Master
and the other as Slave (for information on settings, please refer to the instructions located on the IDE
device). Before attaching the IDE cable, please take note of the foolproof groove in the IDE connector.

7) SATAII0 /1 /2 /3 (SATA 3Gb/s Connectors, Controlled by AMD SB600)

SATA 3Gb/s can provide up to 300 MB/s transfer rate. Please refer to the BIOS setting for the Serial
ATA and install the proper driver in order to work properly.

Pin No.

Definition

1

GND

2

TXP

3

TXN

4

GND

5

RXN

6

RXP

7

GND

2

40

1

39

1

1

7 SATAII 0

SATAII 1

SATAII 2

SATAII 3

7

1

7

1

7

Summary of Contents for GA-MA69VM-S2

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands