GIGA-BYTE TECHNOLOGY GA-970A-D3P User Manual Download Page 15

Page: 15 / 84

- 15 -

Hardware Installation

1-3-2 Installing the CPU Cooler

Follow the steps below to correctly install the CPU cooler on the motherboard. (The following procedure uses
the GIGABYTE cooler as the example.)

Use extreme care when removing the CPU cooler because the thermal grease/tape between the CPU
cooler and CPU may adhere to the CPU. Inadequately removing the CPU cooler may damage the CPU.

Step 1:
Apply an even and thin layer of thermal grease on
the surface of the installed CPU.

Step 2:

Hook the CPU cooler clip to the mounting lug on

one side of the retention frame. On the other side,

push straight down on the CPU cooler clip to hook

it to the mounting lug on the retention frame.

Step 3:

Turn the cam handle from the left side to the

right side (as the picture above shows) to lock

into place. (Refer to your CPU cooler installation

manual for instructions on installing the cooler.)

Step 4:

Finally, attach the power connector of the CPU

cooler to the CPU fan header (CPU_FAN) on the

motherboard.

Downloaded from

www.Manualslib.com

manuals search engine

Summary of Contents for GA-970A-D3P





















































































Search results

Summary of Contents for GA-970A-D3P

Reviews:

Related manuals for GA-970A-D3P

Brands by name

Popular brands

GIGA-BYTE TECHNOLOGY GA-970A-D3P, User Manual

Search results

Summary of Contents for GA-970A-D3P

Reviews:

Related manuals for GA-970A-D3P

Brands by name

Popular brands