GIGA-BYTE TECHNOLOGY G481-HA1 Service Manual Download Page 85

Page: 85 / 124

- 85 -

BIOS Setup

5-3-3

UPI Configuration

Parameter

Description

UPI Configuration

UPI General Configuration

Press [Enter] to configure advanced items.

UPI Status

– Press [Enter] to view the UPI status.

Link Frequency Select

– Selects the UPI link frequency.

– Options available: 9.6GB/10.4GB/Auto. Default setting is

Auto

SNC

– Enable/Disable SNC.

– Options available: Disable/Enable/Auto. Default setting is

Disable

Stale AtoS

– Enable/Disable Stale A to S Dir optimization.

– Options available: Disable/Enable/Auto. Default setting is

Disable

LLC dead line alloc

– Enable/Disable LLC dead line alloc.

– Options available: Disable/Enable/Auto. Default setting is

Auto

Summary of Contents for G481-HA1





























































































































Search results

Summary of Contents for G481-HA1

Reviews:

Related manuals for G481-HA1

Brands by name

Popular brands

GIGA-BYTE TECHNOLOGY G481-HA1, Service Manual

Search results

Summary of Contents for G481-HA1

Reviews:

Related manuals for G481-HA1

Brands by name

Popular brands