Giant VT SERIES Owner'S Manual Download Page 10

 

 

Pag. -10- 

 

Main Spring air pressure 

Rider Weight 

 

[kg] / [lb]

 

Short Travel 

Sag 25-30% 

[psi] 

Long Travel 

Sag 30-35% 

[psi] 

55 kg / 120 lb or less 

90-130 

55-60 kg / 130 lb 

130-135 

60-65 kg / 140 lb 

135-140 

65-70 kg / 150 lb 

140-145 

70-75 kg / 160 lb 

145-150 

75-80 kg / 170 lb 

150-155 

80-85 kg / 180 lb 

155-160 

85-90 kg / 190 lb 

165-170 

90-95 kg / 200 lb 

175-180 

95-100 kg / 209 lb 

185-190 

100 kg / 220 lb or more 

195-250 

 

 

The rear shocks are serviceable and must be returned for maintenance, repair or service, only to an 

authorised Manitou dealer (or the Manitou distributor in your country) once a year or more often if 

the bike is used in extreme conditions. 

This service is not necessarily free of charge! 

 

WARNING:  

All service and maintenance of the rear shocks should only be performed with proper tools 

by an authorised Manitou dealer or by the Manitou distributor in your country.

 

 

 

4-3 Removing the rear shock assembly or pivots. 

 

It is necessary to periodically check the rear shock unit and the suspensions’ pivot points for 

damage or wear. The rear shock unit should be returned to an authorised Manitou dealer or to the 

Manitou distributor in your country to inspect and repair.  

(Note: this is not covered under the terms of the warranty). 

 

WARNING:  

Do not try to disassemble or to replace the rear shock or a pivot by yourself ! 

Improper (dis-)assembly may result in damage to the bicycle or in an accident which can 

cause serious injury or death. Only an authorised Giant dealer should disassemble the rear 

shock or pivots.

 

 

 

Summary of Contents for VT SERIES













Reviews: