+1
3
ALL CLEAR UNIT SELECTION CIRCUMFERENCE SETTING
CLOCK SETTING
ODO SETTING
RESET OPERATION (DST=0, RTM=0, AVG=0, MAX=0)
4
1
2s
MAIN UNIT SETUP (Fig.1)
PROGRAM THE COMPUTER (ALL CLEAR)
1. A battery is already loaded in the main unit when purchased.
2. Hold down the SET button
and RESET button
simultaneously for more than 3
seconds to program the computer and clear all data.
IMPORTANT: Be sure to
program the computer before it is be used, otherwise the computer may run
errors.
3. The LCD segments will be tested automatically after the unit is programmed.
4. Press MODE button
to stop LCD test, then the flickering "KM/H".
UNIT SELECTION
Press MODE button
to choose KM/H or M/H. Then press the SET button
to
store selection.
WHEEL CIRCUMFERENCE
1. Roll the wheel until the valve stem at its lowest point close to the ground, then
mark this first point on the ground.
(Fig. a)
2. Get on the bike and have a helper push you until the valve stem returns to its
lowest point. Mark the second point on the ground. (Sitting on the bike achieves a
more accurate reading since the weight of the rider slightly changes the wheel
circumference).
3. Measure the distance between the marks in millimeters. Enter this value to set the
wheel circumference.
Option: Get a suitable circumference value from the
table.
(Fig. b)
4. Adjust the wheel circumference as the data setting process.
5. Unit will change to the normal operation after this circumference setting.
FUNCTIONS (Fig.3)
:
Current Speed
0.0–199.9Km/h (120.0 Mile/h), 0.1Km/h (Mile/h), +/- 1%
The current speed is always displayed on the upper set when riding. It displays
current speed up to 199.9 Km/h or 120.0 Mile/h (for wheel diameters over 24 inches).
CLK:
12HR or 24HR Clock
1H00M–12H59M or 0H00M–23H59M, 1 Minute, +/- 0.3%
It can display the current time either in 12HR or 24HR clock.
DST:
Trip Distance
0.00–999.99Km (Miles), 0.01Km (Mile), +/- 0.01%
The DST function accumulates the distance data from the last RESET operation as
long as the bike is being ridden.
PRECAUTIONS
1. This computer can be used in the rain but should not be used under water.
2. Don’t leave the main unit exposed to direct sunlight when not riding the bike.
3. Don’t disassemble the main unit or it’s accessories.
4. Check relative position and gap of sensor and magnet periodically.
5. Clean the contacts of the bracket and the bottom of the main unit periodically.
6. Don’t use thinner, alcohol or benzine to clean the main unit or its accessories when
they become dirty.
7. Remember to pay attention to the road while riding.
RTM:
Riding Time
0M00S-59M59S, 1 Second, 0H00M-99H59M, 1 Minute, +/- 0.03%
1. The RTM totals the riding time from the last RESET operation.
2. It displays in 1 second increments when RTM is less than 1 hour and changes to 1
Minute increments after 1 hour. It will restart from zero after 100 hours.
AVG:
Average Speed 0.0–199.9Km/h (120.0Mile/h), 0.1Km/h (Mile/h), +/- 0.1%
1. It is calculated from the DST divided by the RTM. The average data counted is
from the last RESET to current point.
2. It will display "0.0" when RTM is less than 4 seconds.
3. It is updated about one second when RTM is over 4 seconds.
MAX:
Maximum Speed
(Axact 11 only)
0.0–199.9Km/h (120.0Mile/h), 0.1Km/h (Mile/h), +/- 1%
It shows the highest speed from the last RESET operation.
TMP:
Current Temperature °C / °F -10°C ~ 60°C (14°F ~ 140°F)
ODO:
Odometer 0-99999Km (Miles), 1Km (Miles), ± 0.1%
The ODO accumulates total distance as long as the bicycle is running, the ODO data
can be cleared by the All Clear operation only.
: SCAN
1. Auto-Scanning Display Mode.
Press the MODE button
till the symbol is displayed. The computer will change
the display modes in a loop sequence automatically every 5 seconds.
2. Fixed Display Mode.
Press the MODE button
to turn off the symbol and select a desired display
mode; the computer will stop the auto-scanning display operation.
/ : Speed Pacer
(Axact 11 only)
It flashes the speed pacer arrow while the current speed is higher than the
average speed and the down arrow flickers conversely.
BUTTON AND OPERATIONS
MODE BUTTON
Quickly press this button to move in a loop sequence from one function screen to another.
LOCK/SET BUTTON
Press this button 2 seconds to get in or out the setting screens when you want to
reset to bike, or the current time of the CLK.
LIGHT/RESET BUTTON
(Fig. 6)
1. Light for 4 seconds after each press.
2. The symbol " " will apper to indicate the EL back-light functuon is at working status.
CLOCK SETTING (Fig.2)
1. Change the LCD display to CLK screen.
2. Press the SET button
to enter the clock adjusting screen to setting the clock.
3. A quick press of the MODE button
to select 12HR or 24HR.
4. Adjust the clock data as the data setting procedures.
RESET OPERATION (Fig.4)
1. Hold down the RESET button
till the LCD screen is blank, then release it. The
computer will reset AVG, DST, RTM and MAX data from stored values to zero.
2. It cannot reset ODO, CLK.
AUTOMATIC START/STOP
The computer will automatically begin counting data upon riding and stop counting
data when riding is stopped. The flickering symbol " " indicates that the computer
is at start status. To preserve battery, this computer will automatically switch off and
just displays the CLK data when it has not been used for about 15 minutes. The
power will be turned on by pressing the SET button
.
KEY-LOCK (Fig. 5)
To protect you computer, you may can press the lock button to lock the MODE button
Whenever you press the lock button, the functions of the MODE button
will be disabled.
You may can unlock the MODE button
by pressing the lock button
again.
AUTO SLEEP MODE
To preserve battery, this computer will automatically switch to sleep mode and just
displays the CLK data when it has not been used for about 15 minutes. The power
will be turned on automatically by riding the bike or by pressing the button.
LOW BATTERY INDICATOR
1. The symbol " " will appear to indicate the battery is nearly exhausted.
2. Replace battery with a new one within a few days after the symbol was appeared,
otherwise the stored data may be lost when the battery voltage is too low.
BATTERY CHANGE (Fig. c)
1. All data will be cleared when battery is replaced.
2. This computer allows you to re-key in data of ODO which you have had rode
after replacing battery.
3. Keep record the ODO data before you remove the old battery.
4. Replace with a new CR2032 battery in the compartment on the back
of the computer with the positive (+) pole toward the battery cap.
5. Program the main unit again.
English
Sensor:
No Contact Magnetic Sensor.
Battery Type:
3.0V Battery X 1 (Typical No. CR2032)
Battery Operating Life:
CR2032 in Main Unit About one year
(based on the average riding time of 1.5 hours per day)
Dimensions/Weight:
34x 52 x 15mm / 21g
Wheel Circumference Setting:
1mm - 3999mm (1mm increment)
Operation Temperature:
0°C ~ 50°C (32°F ~ 122°F)
Storage Temperature:
-10°C ~ 60°C (14°F ~ 140°F)
2s
TROUBLE SHOOTING
Check the following before taking unit in for repairs.
PROBLEM CHECK ITEM REMEDY
1. Is the battery dead?
2. Is there incorrect battery installation?
1. Is it at the recalibrating or clock setting
screen?
2. Are the contacts between the main
unit and the bracket poor?
3. Are the relative positions and gap of
sensor and magnet correct?
4. Is the wire broken?
5. Is the circumference correct?
Did you leave main unit under direct sunlight
when not riding the bike for a long time?
Is the temperature below 0°C (32°F)?
No
display
No
current
Speed or
incorrect
data
Irregular
display
LCD is
black
Display
is slow
1. Replace the battery.
2. Be sure that the positive pole of the
battery is facing the battery cap.
1. Refer to the adjusting procedure and
complete the adjustment.
2. Wipe contacts clean.
3. Refer to Installarions and readjust
data correctly.
4. Repair or replace wire.
5. Refer to "CALIBRATION" and enter
correct value.
Refer to the "MAIN UNIT SETUP"
and initiate the computer again.
Place main unit in the shade to return
to normal state.No adverse effect on
data.
Unit will return to normal state when
the temperature rises.
3s
+
CYCLE COMPUTER
MODE
LOCK/
SET
LIGHT/
RESET
BATTERY CHANGE
Tire Size
Circumference
Nunber
18 Inch
1436 mm
20 Inch
1596
22 Inch
1759
24x1.75
1888
24 Inch
1916
24x 1 3/8
1942
26x1.40
1995
26x1.50
2030
26x1.75
2045
26x1.95
2099
26x2.1
2133
700C TUBULAR
2117
700x20C
2092
700x23C
2112
700x25C
2124
700x28C
2136
700x32C
2155
700x35C
2164
700x38C
2174
27.5 Inch
2193
28 Inch (700B)
2234
28.6 Inch
2281
b.
POPULAR TIRES
CIRCUMFERENCE
REFERENCE TABLE
15m
WHEEL CIRCUMFERENCE
a.
2nd 1st
SEGMENTS
LCD
AUTO TEST
+1
+1
+1
CLOCK DST RTM AVG MAX TMP ODO SCAN
OK!
0
~
23
0
~
5
0~3
0~9
0~9
0~9
END SETTING
0~9
2s
6.
Key-lock
EL Back-light
Data Setting Mode
c.
0~3
2s
OK!
2s
MODE
Low battery indicator
5.
Auto Sleep and
Key-lock on
ON
OFF
Key-lock off
DST
RTM
AVG
MAX
2
WIRED
/
(AXACT 11 only)
(AXACT 11 only)
Gasket
Battery
CR2032
Battery
cap
3V
CR2032
+
3V
CR2032
+
Screwdriver
Screw
CR2032
