background image

THE CONTENT OF THIS DOCUMENT IS GIANT ELCT.LTD. INTELLECTUAL PROPERTY AND IS THE 
PROPERTY OF GIANT, IT IS TO BE TREATED AS STRICTLY AND IS NOT BE DISCLOSED, 
REPRODUCED, OR USED EXCEPT AS AUTHORIZED IN WRITING BY GIANT ELECTRONIC LTD. IN 
CONNECTION WITH THE MANUFACTURE,MAINTENANCE AND USE OF THE GIANT EQUIPMENT 
WHICH IT PERTAINS. COPYRIGHT @GIANT ELECT. LTD, ALL RIGHTS RESERVED. 
 

 

GIANT ELECTRONICS LTD. 

Title:  Alignment Procedure 
Model: T6500

 

  

A.  PCB LEVEL  (Test Condition: under CH15) 

NO ITEM 

ALIGNMENT 

METHOD 

REMARK 

11. VOX 

Detector 

 

1. Set VOX level at 1. 
2. Set AF level  at 14.2 +/- 0.2 mV,1KHz at TP116. 
3. Unit start to transmit. 
4. Set AF level at 10.8  +/- 0.2mV,1KHz at TP116. 
5. Unit stop transmit. 
6. Set VOX level at 2. 
7. Set AF level at 8.4 +/- 0.2mV,1KHz at TP116. 
8. Unit start to transmit. 
9. Set AF level at 5.8 +/- 0.2mV,1KHz at TP116. 
10. Unit stop transmit. 
11. Set VOX level at 3 
12. Set AF level at 4.0 +/- 0.2mV,1KHz at TP116. 
13. Unit start to transmit. 
14. Set AF level at 2.7 +/- 0.2mV,1KHz at TP116. 
15. Unit stop transmit. 

 

12. IVOX 

Detector 

 

1. Set VOX level at 1. 
2. Set AF level  at 14.2 +/- 0.2 mV,1KHz at TP116. 
3. Unit start to transmit. 
4. Set AF level at 10.8  +/- 0.2mV,1KHz at TP116. 
5. Unit stop transmit. 
6. Set VOX level at 2. 
7. Set AF level at 8.4 +/- 0.2mV,1KHz at TP116. 
8. Unit start to transmit. 
9. Set AF level at 5.8 +/- 0.2mV,1KHz at TP116. 
10. Unit stop transmit. 
11. Set VOX level at 3 
12. Set AF level at 4.0 +/- 0.2mV,1KHz at TP116. 
13. Unit start to transmit. 
14. Set AF level at 2.7 +/- 0.2mV,1KHz at TP116. 
15. Unit stop transmit                                                               

 

13. 

Rx Audio test 

1. Set RX mode CH7. 
2. Set SG RF level to –50dBm with 1.5KHz deviation 

1KHz modulation Signal. 

3. Adjust L517 to provide minimum distortion & max 

output level at TP117. 

4. Rotate the volume switch to the position, which give a 

Max audio output  at TP117. 

5. Check Max audio output level >1500mV. 
6. Check Rx current <150mA. 
7. Check the 1KHz distortion <= 5%. 
8. Set SG RF level to –119dBm with 1.5kHz deviation at 

1KHz audio frequency. 
a). Check SINAD sensitivity <= -119dBm. 

     @12dB SINAD at  TP117. 

 

 
 
 
 
 
 
 
 

Summary of Contents for T6500








Reviews: