Ghost Controls HDP1 Installation And Owner'S Manual Download Page 56

Page: 56 / 68

P U S H - T O - O P E N

PROGRAMMING THE OPEN LIMIT FOR A PUSH-TO-OPEN

INSTALLATION

The

OPEN

limit is when the operator is extended and the gate is in the closed position.

IMPORTANT

ONLY THE OPERATOR ARMS’ EXTENDED LIMIT IS ADJUSTABLE AND CAN BE SET WITH THE CONTROL

BOARD. THE ARMS’ RETRACTED POSITION IS FIXED AND IS NOT ELECTRONICALLY ADJUSTABLE.
THE CLOSED POSITION IS SET BY HARDWARE MOUNTING ONLY. Please refer to the hardware installation to

make sure the retracted position is properly set/installed.

Installation Type

Retracted Position

Extended Position

Push-To-Open

Gate at the fully

CLOSED

position (not

electronically adjustable)

Gate at the

OPEN

position (electroni-

cally adjustable)

TURN THE CONTROL BOX ON

STEP 16.

Setting the open limit.

A. Press and hold the

JOG OPEN

buttons on the gate system control

board until the gate reaches the

desired OPEN position. The gate

can move only if pressure is maintained. Releasing the

JOG

button

will stop the gate immediately.

B. Both

JOG

OPEN

JOG CLOSE

buttons are needed to ‘fine’ tune your

desired OPEN position.

STEP 17.

Press and hold the 1st set limit button on the control panel until it beeps, then release.

STEP 18.

Press the transmitter button to activate the gate and let the gate close fully. you should

hear a single beep.

When the gate reaches its

CLOSED position, the control board will sound a single beep, confirming the CLOSED limit has

been set.

Summary of Contents for HDP1





































































Search results

Summary of Contents for HDP1

Reviews:

Related manuals for HDP1

Brands by name

Popular brands

Ghost Controls HDP1, Installation And Owner'S Manual

Search results

Summary of Contents for HDP1

Reviews:

Related manuals for HDP1

Brands by name

Popular brands