Ghibli & Wirbel C 150 U13, Use And Maintenance

Page: 18 / 24

www.ghibliwirbel.com
Professional Cleaning Machines Since 1968
ENGLISH - 4
2.2 COMPONENT
ASSEMBLY
2.2.a - Assembling the cable reel
supports (Figs. 3/5)
The reel supports supplied must be mounted
directly on the handle shaft:
- Fit the short coupling (4) into the long
coupling (5) (Fig. 3).
- Tighten the knob (6) on the screw (7),
keeping the latter to the right (Fig. 4).
- The hook (8) of the support can be ro-
tated depending on usage (Fig. 5).
- Place one support on the top of the han-
dle and a second support on the bottom.
2.2.b - Pad assembly (Figs. 6/9)
- Tilt the machine, pivoting, with the handle
straight (9), with your feet on the wheels
(10) and place it on the handle (Fig. 6).
- Unscrew the ring nut (11) using the han-
dle (12) supplied (Fig. 7).
- Mount the pad (13) on the pad holder
(14) (Fig. 9).
- Centre the pad (13) with the central guide
(15) on the pad holder (14) and make
sure the outer perimeter of the pad (13)
corresponds with the outer perimeter of
the pad holder (14) and then lock it on
the pad holder’s teeth pressing down with
your fingers (Figs. 8-9).
- Use the pad for high-speed polishing
(Gorilla or Cream Colour).
WARNING:
Use only pads supplied by the manufac-
turer for the specific machine model.
Using other types of pads can compro-
mise the safety of the machine.
2.2.c - Electrical spray accessory
assembly (Optional)
(Figs. 10/16)
- Loosen the knob (16) of the handle’s up-
per support (17) (Fig. 10).
- Make sure that the lower support (18)
rests on the plate (19) located on the han-
dle rod (Fig. 11).
- Place the accessory (20) on the lower
support (18), taking care to align the cou-
pling tab (21) with its housing (22) (Fig.
12).
- Lower the upper coupling (23) and attach
it to the coupling tab (24) on the top of the
accessory (20) (Fig. 13).
- Tighten the knob (26) of the handle’s up-
per support (23) (Fig. 13).
- Connect the power supply (26) to the
auxiliary socket (27) (Fig. 14).
- Fit the nozzle (28) on the right part of the
machine, inserting the plate (33) inside
the casing (29) and the knob screw in the
dedicated (30) housing (31), then tighten
the knob (30) (Fig. 15).
- Make sure the nozzle (32) is in the hori-
zontal position. The spray angle is 120
degrees, the nozzle position may be
adjusted depending on specific require-
ments (Fig. 16).
2.2.d - Filling the tank (Fig. 17)
- Unscrew the tank (34) and remove it.
- Fill it with water and polishing wax.
For dosing, refer to the instructions pro-
vided by the manufacturer of the polish-
ing wax.
- Insert the suction tube (35) into the tank
(34) and fully tighten.
2.2.e - Paper dust collection bag as-
sembly (Figs. 18/19)
The machine is delivered with the bag al-
ready mounted.
- Lift the lid (36) and check that the bag
(37) is correctly positioned (Fig. 18).
Manuale GH30-925_1ed_10-2017.indd 4 19/10/17 16:59