Gharmglow RECTANGULAR GAS FIREPIT Owner'S Manual Download Page 11

LIGHTING INSTRUCTIONS:

Follow the instructions exactly.

1. REMOVE THE FIREPIT COVER before attempting to light the burner so that gas fumes do not

accumulate inside the firepit. An explosion could occur if firepit cover is down.

2. Check that the burner control knob and the cylinder valve are turned to the "OFF" position.

3. Turn on the fuel supply by rotating the cylinder valve knob counter-clockwise to full open.

4. DO NOT stand with head, body, or arms over the firepit when lighting.

LIGHTING THE BURNER:

1. Open door of front panel to view control panel.

2. Remove cover before lighting burner.

3. Make sure control knob is in OFF position.

4. Push and turn control knob counter-clockwise to IGNITE.

5. Continue to push knob in for 30 seconds to light burner. You will hear a

clicking sound of the electronic igniter.

6. If ignition does NOT occur in 30 seconds, turn control knob to OFF, wait 5

minutes to allow gas to dissipate and repeat lighting procedure.

7. Once burner is lit, release the control knob and adjust to desired heat output.

8. To turn off, turn control knob clockwise until it locks in OFF position.

Note:

Turn off LP supply at cylinder when Firepit is not in use.

MATCH LIGHTING THE BURNER:

1. Open door of front panel to view control panel.

2. Remove cover before lighting burner.

3. Make sure control knob is in OFF position.

4. Strike a long wooden match and place approximately 1/2" 

(1 to 2 cm) from the side of the burner.

5.  Turn on the burner control knob to the "HIGH" position. The

burner should light within 5 seconds.

6. If the burner does not light, turn the control knob to "OFF" and

wait 5 minutes for gas to dissipate and repeat lighting procedure.

7. Once burner is lit, release the control knob and adjust to desired

heat output.

8. If the burner does not light within the first few attempts of match

lighting, there is a problem with the gas supply. Turn off the gas
at the burner 

and

cylinder. 

DO NOT

attempt to operate the firepit

until the problem is found and corrected. See "Trouble Shooting"
section of this manual.

WARNING

10

WARNING

Read, understand and follow all warnings and instructions contained in this manual. DO NOT skip
any of the warnings and instructions contained in the preceding sections of this manual.

ME

DIU

IGN

ITE

HIGH

OFF

Battery 

Compartment

Burner

Long Match

Summary of Contents for RECTANGULAR GAS FIREPIT





















Reviews: