GFA ELEKTROMAT SI 8.20-25,00 10003369 10011 Installation Instructions Manual Download Page 8 | Manualshive

Page: 8 / 20

background image

8

Installation

The descriptions below apply to general door specifications. The specifications of the door
manufacturer must also be observed during installation.

Warning - Potential injury or danger to life!



During installation, be sure to use a lifting device that has a sufficient load-
carrying capacity.

▶

Thoroughly grease the door shaft.

BAGAE01001_Z003

▶

Mount the keys. Observe possible variants
Ⓐ or Ⓑ.

BAGAE01002_Z003

«
...
6
7
8
9
10
...
»

Summary of Contents for ELEKTROMAT SI 8.20-25,00 10003369 10011





















Reviews:

No comments

Related manuals for ELEKTROMAT SI 8.20-25,00 10003369 10011

Brand: 4Ddoors Pages: 3

Brand: 4Ddoors Pages: 36

Brand: King gates Pages: 12

Brand: Motorline professional Pages: 14

Brand: O&O Pages: 24

Brand: Topens Pages: 18

SPACELITE HT150

Brand: BUTZBACH Pages: 45

Brand: FAAC Pages: 14

Brand: Key Automation Pages: 96

Brand: Winco Pages: 8

Brand: Nice Pages: 68

Brand: Nice Pages: 132

Brand: Nice Pages: 136

Brand: Parkside Pages: 16

Brand: Tesco Pages: 2

Brand: CAME Pages: 16

PRATICO SYSTEM BX Series

Brand: CAME Pages: 18

Brand: CAME Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands