GEZE Powerdrive PL Pre-Installation Instructions Download Page 5

Powerdrive product family

5

Fundamental safety notes

2.3  Safety-conscious working

 

à

Secure workplace against unauthorised entry.

 

à

Use only the cables specified on the cable plan provided. Cables must be shielded in compliance with the 

wiring diagram.

 

à

Secure loose, internal drive cables with cable ties.

 

à

Before working on the electrical system:

 

à

Disconnect the drive from the 230 V mains and secure it against being switched back on again. Check isolation 

from power supply.

 

à

Disconnect the control unit from the 24 V rechargeable battery.

 

à

Note that if an Uninterruptible Power Supply (UPS) is used, the system will still be supplied with voltage  

despite the fact that the power supply is disconnected.

 

à

Always use insulated wire-end ferrules for wire cores.

 

à

Make sure of sufficient lighting.

 

à

Risk of injury with opened drive. Hair, clothing, cables, etc. can be drawn in by rotating parts.

 

à

Risk of injury caused by unsecured crushing, impact, drawing-in or shearing spots.

 

à

Risk of injury due to sharp edges on the drive and door leaf.

 

à

Risk of injury during installation through freely moving parts.

2.4  Environmentally conscious working

 

à

When disposing of the door system, separate the different materials and have them recycled.

 

à

Do not dispose of batteries and rechargeable batteries with household waste.

 

à

Comply with the statutory regulations when disposing of the door system and the batteries/rechargeable 

batteries.

2.5  Safety note related to transportation and storage

 

X

Do not throw, do not drop.

 

X

Avoid heavy impacts.

 

à

Storage temperatures under –30 °C and above +60 °C can result in damage to the device.

 

à

Protect against humidity.

 

à

Dry, well ventilated, closed, weather-proof and UV-protected rooms are suitable as storage areas.

2.6  Qualification

Observe country-specific regulations!

Applicable in Germany: 

Companies that carry out the pre-assembly of sliding door drives for escape routes must be licensed as an  

expanded manufacturing facility by the testing institution that issued the type approval certificate.

Summary of Contents for Powerdrive PL





















Reviews: