GESTRA ZK 313 Installation Instructions Manual Download Page 54

Page: 54 / 60

Disposing of the equipment

Caution

Environmental damage may be caused by
poisonous fluid residues.



Before disposing of the equipment
make sure that it is clean and free of
fluid residues.



For the disposal of all materials
observe the pertinent legal regulations
concerning waste disposal.

Materials

Component

ASME

Body

1.0460

A105

1.5415

–

1.7383

A182F22

1.4903

A182F91

Upper part of body

1.0460

A105

1.4903

A182F91

Threaded bolt

1.7709
1.4980

A193B16

Nuts

1.7709
1.4980

A194-7

Technical data

Dimensions and weights

For information on dimensions and weights please
see data sheet.

For information on dimensions and weights of the
actuator please refer to the documents provided by
the manufacturer of the actuator.



For more information please contact the
manufacturer.

Summary of Contents for ZK 313





























































Search results

Summary of Contents for ZK 313

Reviews:

Related manuals for ZK 313

Brands by name

Popular brands

GESTRA ZK 313, Installation Instructions Manual

Search results

Summary of Contents for ZK 313

Reviews:

Related manuals for ZK 313

Brands by name

Popular brands