Gerni MC 5M Operating Instructions Manual Download Page 19

19

1)

 Options / model variants

Original instructions       

MC 5M - MC 6P - MC 7P

5.2   Some typical cleaning tasks
5.2.1 Agriculture

Task

Accessories

Method

Stables
Pig Pens, Sties

Cleaning of 
walls, floors and 
equipment.
 
Detergents

Chemical Foam 
Injectors
Foam lance
Powerspeed lance
Floor Cleaner

Universal
Alkafoam

Disinfectant 
DES 3000
DES 4000

1.  Soaking – apply foam to all surfaces (bottom to top) 

and wait for approx. 10 - 30 minutes.

2.  Remove the dirt from surfaces with the high 

pressure lance or chosen accessory. Again, clean 
from bottom to top on vertical surfaces.

3.  To flush away large quantities of dirt, change to low 

pressure mode and use the higher flow to push 
away the dirt.

4.  Use recommended disinfectant products and 

methods to ensure hygiene. Apply DES 3000 
disinfectant once the surfaces are perfectly clean.

Machinery
Tractors
ploughs etc.

Detergent injection
Powerspeed lances
Curved lances and 
underchassis washers
Brushes

1.  Apply detergent to vehicle or equipment surfaces in 

order to soften up dirt and grime. Apply from bottom 
to top.

2.  Proceed with cleaning using the high pressure 

lance.  Clean again from bottom to top.  Use 
accessories to clean in difficult to reach places. 

3.  Clean fragile areas such as motors, rubber at lower 

pressure levels to avoid damage.

5.2.2 Vehicle

Task

Accessories

Method

Vehicle bodywork

Detergents

Standard lance
Detergent injection
Curved lances and 
underchassis washers
brushes

Aktive Shampoo
Aktive Foam
Sapphire
Super Plus
Aktive Wax 
Allosil
RimTop

1.  Apply detergent to vehicle or equipment surfaces 

in order to soften up dirt and grime. Apply from 
bottom to top. In cases of particularly dirty vehicles, 
pre-spray with a product such as Allosil in order 
to remove traces of insects etc, then rinse at low 
pressure and apply normal car cleaning detergent. 
Let detergents settle for 5 minutes before cleaning 
off. Metallic surfaces can be cleaned using RimTop.

2.  Proceed with cleaning using the high pressure 

lance.  Clean again from bottom to top.  Use 
accessories to clean in difficult to reach places.  
Use brushes in order to add a mechanical cleaning 
effect. Short lances can help for cleaning of motors 
and wheel arches. Curved lances or undercarriage 
washers  can be valuable for the cleaning of car 
underchassis and wheel arches.

3.  Clean fragile areas such as motors, rubber at lower 

pressure levels to avoid damage.

4.  Apply a liquid wax using the pressure washer in 

order to protect the bodywork from pollution.

Summary of Contents for MC 5M






























Reviews: