Notice for Operation
P.9
Operating Instructions
P.8
- The appliance will not start operation until the blender jar is placed on the unit base, which is for safety
purpose.
- Insert the measuring cup to the lid (align the arrow on the cup to the symbol on the lid and turn it to
position). Then press down the lid to the blender jar to close. To open, pull up by the flap of the lid.
- During operation, close the lid tightly to avoid injuries due to spilling or splashing of hot liquids.
- Wind part of the power cord underneath the unit base. Prevent rubber foot from stepping on the power cord.
- When the food is too thick or there is too little liquid in the jar, the motor will be dragged to a low speed or stop
to operate. Hence, when blending thick and sticky food, start blending from low to high speed. If it is still unable
to blend, disconnect the power and stir the food inside the jar using a rubber stirrer to drive out the air trapped
in food. Then close the lid and switch on the blender to continue the operation.
- When overheating is sensed, the temperature monitoring system will be activated and would stop the operation
of the motor. In this case, put the appliance in a place with good ventilation to cool it down for 45 minutes. The
system will be reset and you may resume the operation of the appliance.
- Keep hands and utensils out of the container while the motor is running to prevent the possibility of severe
personal injury and/or damage.
- In making hot beverage or soup (such as soy milk, porridge, bisque, etc.), please ensure that the lid is secured
tightly to the jar to prevent it from falling. Please be advised to start the operation at low speed first and then
gradually increase the speed, or simply use the “Pulse” mode.
- When making sauces (eg. almond sauce, jam and sesame sauce), stuffing and nuts, put in between 2 and 3
cups of ingredients. The amount should neither be too large or too little. Keep the blending time below 2 min to
prevent any burnt smell due to overheating. Too much ingredients may lead to overloading and overheating of
the motor. In this case, wait till the motor temperature falls before operating again.
- Please put liquid and soft food into the jar before putting in hard food or ice cubes.
- When the operation finishes, please wait until the blade assembly comes to a complete stop before taking up
the blender jar.
- If you feel a burnt smell from the blender, stop the operation immediately. It may be caused by the abrasion at
the rubber cushion base if it is not properly assembled.
- Do not operate continuously for over 10 minutes each time.
Preset Programmes
Press set mode icons for programme selection and the selected icon will flash. Press button within 5 seconds and the
appliance will start operation at the selected programme and speed, and enter stand-by mode after completion.
Icon
Programme
Bisque
Sauce
Vegetable
Soy Milk
Nuts
Smoothie
Operation time
countdown display
Operation time
countdown display
Operation time
countdown display
Operation time
countdown display
Operation time
countdown display
Operation time
countdown display
Descriptions
LCD Display
Accelerate to speed 7 in 5 sec. Then accelerate
to speed H in 5-10 sec and stay at this speed
until finish. Total time is 8 min.
Speed H for 30 sec and pause for 2 sec;
then speed 6 for 10 sec and pause for 2 sec;
then speed H for 60 sec and pause for 2 sec;
finally speed 6 for 10 sec. Total time is 1 min 56
sec.
Accelerate from speed 1 to speed 5 in 5 sec,
and run at speed 5 for 25 sec; then speed 8
for 30 sec; finally speed H until finish. Total
time is 6 min.
Speed H for 8 sec and pause for 2 sec.
Run in cycles until finish. Total time is 30 sec.
Speed 8 for 2 sec and pause for 1 sec.
Repeat for 5 cycles. Then speed H for 45 sec.
Total time is 1 min.
Speed H for 4 sec and stop 1 sec
.
Repeat this process
.
Then speed H for 30 sec
.
Total duration is 40 sec.
Pulse Button
At stand-by or any operation mode, press this button and it will flash at 0.5 second at intervals. Press and hold
this button within 5 seconds to start operation. Time indicator will start counting from 00:01. The motor will start
running at speed H. Time indicator will show 10:00 and the appliance will enter stand-by mode.
If this button is released, the appliance will stop operation and time indicator will stop counting. If there is no
operation after the appliance stops running for 5 seconds, it will enter stand-by mode.
