• •••• •• •• •• •• •• •• •
SPECIFICATIONS
25-400Hz
500-8KHz
25-400Hz
25-400Hz
18 dB per Octave 3rd Order Butter worth
12 dB per Octave 2nd Order Butter worth
Single Octave 0 dB to 18 dB [variable] at 45Hz
20K Ohms
100 Ohms
1:2 [+6 dB]
5 volts max
14.4 volts DC negative ground
Power source:
0.5 amp max
Input current:
0.01% THD at 1 V output level
Distortion:
10Hz -30Hz -3 dB
Frequency response:
>95 dB
S/N radio [A weighted]:
60 dB
Separation:
Crossover frequencies
[continuously variable]:
Front High-pass:
Rear High-pass:
Subwoofer:
Crossover slope rate:
Low-Pass:
High-Pass:
Subwoofer boost:
Input impedance:
Output impedance:
Output gain:
Output voltage level:
Dimensions:
FEATURES AND SPECIFICATIONS SUBJECT TO CHANGE AND/OR IMPROVEMENT WITHOUT NOTICE
[X1]:
[X20]:
5.5 W x 7.5 L x 1.75 H
[143mm W x 193.6mm L x 43.6mm H]
FEATURES
EXCLUSIVE INFINITE CROSSOVER DESIGN
ASYMMETRICAL ELECTRONIC CROSSOVER DESIGN
DC/DC REGULATED SWITCHING POWER SUPPLY
This power supply design provides constant voltage to the crossover regardless of the battery's
voltage to ensure consistent output performance at all times.
This design also eliminates switching
noise due to voltage fluctuation.
FREQUENCY MULTIPLIER
The front high-pass section is equipped with a frequency multiplier switch that can be used to
multiply the crossover Frequency points.
With the additional selectable crossover points, system
setting becomes an art of precision.
PARALLEL INPUT SWITCH
For a source unit having a single pair of signal outputs, an adapter is needed to split the source
signal for the front and rear inputs. With the mobile electronic crossover, by engaging the parallel
input feature, an external adapter is no longer necessary.
FRONT /REAR INPUTS WITH
FRONT /REAR /SUBWOOFER OUTPUTS
The mobile electronic crossover features front and rear preamp inputs with front and rear outputs,
as
well as constant subwoofer output that is independent of the front/rear fader position on the source
unit.
BASS BOOST CIRCUITRY WITH QUASI-PARAMETRIC EQUALIZATION
A sealed enclosure causes a woofer's frequency response to roll off at a rate of 12 dB per octave
below the enclosure's resonant frequency.
Our Bass Boost Circuitry with Quasi-Parametric Equalization provides a single octave boost of
12 dB at 45 Hz to ensure smooth and accurate bass response.
ADJUSTABLE OUTPUT LEVEL STEREO/MONO SUBWOOFER GOLD PLATED RCA
CONNECTORS
-1-
-2-
CONTROLS,
INDICATORS AND TERMINALS
1.POWER INPUT TERMINAL [RED]
To be connected to the positive terminal of your vehicle battery or other co12V source.
2.REMOTE TURN-ON INPUT TERMINAL [ORANGE ]
To be connected to the remote control wire or antenna lead of the source unit for remote ON/OFF.
3.GROUND INPUT TERMINAL [BLACK ]
To be wired to the vehicle's chassis ground.
4.POWER INDICATOR
This indicator lights up when the internal switching power supply is activated and the unit is operational.
5.LEFT/RIGHT FRONT CHANNEL SIGNAL INPUTS
To be connected to the front channel output of the source unit.
6.PARALLEL INPUT SWITCH
"IN": When the parallel input is at the
"IN"
position, the input signals coming in through the front channel
signal inputs are split and directed to the front and rear channels simultaneously. [This feature is to be
engaged where the source unit has no separate front, rear or subwoofer channel outputs.]
“
":If the source unit has independent front and rear channel outputs, disengage the parallel input by
OUT
sliding the switch to the
"OUT"
position.
Summary of Contents for G-Cross3W
Page 1: ......
