连接接口
连接接口
3
4
Product parameters are project to change without prior
notice
.
连接接口
Trouble Shooting
If any trouble with operation, please follow these steps to do troubleshooting:
Please make sure you have followed the instruction to install the device;
Please confirm if the RJ45 cable order is in accordance with the EIA/TIA568A or 568B industry
standards;
The power supply of each PoE port is no more than 30W; please do not connect the PoE device
whichexceeds the maximum PoE power supply;
Please replace a failure device with a proper one to check if the device is broken;
Please contact your vendor if trouble still exists.
Item
Description
Downlink
Ports
8x10/100/1000Base-T
Ethernet
Ports
(
PoE)
Uplink
Ports
1x 10
/
100
/
1000Base
-
TEthernet Ports & 1x 1000Base
-
X
SFP Port
Network
Standard
Support
IEEE
802
.
3
/
802
.
3u/IEEE802.3ab/IEEE802.3z/IEEE802.3x
Switch
Capacity
20Gbps
Packet Forwarding Rate
14Mpps
Exchange
Type
Storage&Fowarding
Buffer
1M
MAC
Address
List
4K
PoE Standard
802.3af/at(PSE)
PoE
Mode
End
-
span
PoE
Power
S
upply
1
/
2
(+)，
3
/
6
(-)
PoE
Output
Single
PoE
Output
≤
30
W(
54V DC), Whole machine PoE output
≤
120W
Surge Immunity
6KV
ESD
Protection
Contact
discharge 6K
,
Air
discharge
8KV, Per:
IEC61000
-
4
-
2
Voltage
Input
DC 48V~57V
Power Consumption
5W
Operation
Temperature
-10
℃~+
45
℃
Storage
Temperature
-
40
℃~+
85
℃
Operation
Humidity
5%-95%
(
Non
-
condensing
)
Dimensions
(
LxWxH)
200mm
×
101
.
8mm
×
27mm
Material
Metal
Color
Black
Weight
500g
Specification
4口百兆以太网交换机
8 Ports Full Gigabit PoE Ethernet Switch
8 Ports Full Gigabit PoE Ethernet Switch
P
in
color
white/green
green
blue
white/orange
white/blue
white/brown
orange
brown
1
2
3
4
5
6
7
8
Pin
color
1
2
3
4
5
6
7
8
white/green
green
blue
white/orange
white/blue
white/brown
orange
brown
EIA/TIA 568A
EIA/TIA 568B
RJ
45
Making
Method
Tools to make RJ45: wire
crimper, network tester.
Wire sequence
of
RJ45
plug should conform with EIA/TIA568A or EIA/TIA568B standard.
1) Strip off the 2cm insulating layer to expose the 4 pairs UTP cable;
2) Seperate the 4 pairs of UTP cable and straighten them;
3) Line up the 8 separated pieces of cables per EIA/TIA 568A or 568B;
4) Cut the cables to leave 1.5cm bare wire and make sure 8 thread ends are flat and neat ;
5) Insert 8 cables into RJ45 plugs, make sure each cable is inserted in each pin;
6)Then use wire crimper to crimp the RJ45;
7) Do the above 5 steps again to make the another end of the twisted pair and make sure
consistent cable order between two ends ;
8) Using network tester to test the cable.
Notice
When choose RJ-45 make sure if one end is EIA/TIA568B,the other end should also be EIA/TIA568B.
When choose RJ-45 make sure if one end is EIA/TIA568A,the other end should also be EIA/TIA568A.