Genie GCL NEMA 4 Installation Supplement Manual Download Page 2

NEMA 4 & 4X High Voltage Wiring

• 

DO NOT apply power to operator until instructed to do so.

• 

The Genie Company recommends that line voltage wiring be performed by a qualified electrician.

• 

Be sure that electrical power has been disconnected from the input power wires being connected to the 

operator prior to handling these wires. An appropriate lock-out /tag-out procedure is recommended.

• 

Line voltage wiring must meet all local building codes.

• 

Make sure operator voltage, phase and frequency nameplate ratings are identical to the job site line 

voltage ratings.

• 

Input power wiring must be properly sized for the operators amperage rating located on the nameplate.

• 

To reduce the risk of electric shock, make sure the chassis of this unit is properly grounded.

WARNING

!

AVERTISSEMENT

!

1.  Remove LINE VOLTAGE INPUT PLUG and install proper liuqid tight fittings and 1/2”conduit.

2.  Route proper LINE VOLTAGE wires into operator.

3.  Locate LINE INPUT terminals on circuit board. Using correct connectors, attach wires to LINE INPUTS, and 

GROUND terminal. • Keep low voltage and line voltage wires separate.

• 

Route all line voltage wires as shown.

• 

Plug all unused conduit holes.

NOTE:

 

LIQUID-TIGHT CONDUIT AND FITTINGS ARE NOT PROVIDED

NOTE

: ONLY USE HOLES PROVIDED IN ELECTRIC BOX. DO NOT DRILL HOLES IN BOX OR COVER.

• 

NE PAS mettre l’opérateur sous tension avant d’y être invité. 

• 

The Genie Company recommande que le câblage au secteur soit effectué par un électricien qualifié.

• 

Assurez-vous que l’alimentation électrique a été déconnectée des câbles d’alimentation d’entrée 

connectés à l’opérateur avant de manipuler ces câbles. Une procédure de verrouillage/étiquetage 

appropriée est recommandée.

• 

Le câblage au secteur doit satisfaire à tous les codes de construction locaux.

• 

Assurez-vous que les valeurs nominales de la plaque signalétique pour tension, phase et fréquence de 

l’opérateur correspondent à celles des tensions de l’alimentation sur site.

• 

La capacité du câblage d’entrée doit correspondre à la valeur nominale de l’ampérage des opérateurs 

indiquée sur la plaque signalétique.

• 

Pour réduire le risque de choc électrique, assurez-vous que le châssis de l’unité est correctement mis à la 

terre.

Summary of Contents for GCL NEMA 4



















Reviews: